How to Model Large-Strain Viscoelasticity in COMSOL Multiphysics®

Ed Gonzalez | October 11, 2016

Many polymers and biological tissues exhibit viscoelastic deformation, which has a time-dependent response even if the loading is constant in time. Linear viscoelasticity, where the stress depends linearly on the strain and strain rate, is a common approximation. We usually assume that the viscous part of the deformation is incompressible, so the volumetric deformation is purely elastic. In COMSOL Multiphysics® 5.2a, you can model large-strain viscoelasticity besides linear viscoelasticity. See how to use this material model in a biomedical application.

Read More

Linus Andersson | September 29, 2016

Perforations, in mufflers for example, enable partial sound transmission between chambers as well as in and out of pipes. When simulating perforates, it’s possible to draw and mesh each hole, but this increases the time it takes to solve the model. For a more efficient approach, we can apply a semitransparent boundary. Here, we’ll discuss several techniques for doing so as well as describe a method for computing the transfer impedance of the perforate.

Read More

Categories

Caty Fairclough | September 26, 2016

The fans in an airplane’s turbofan engine are one of its main sources of noise. In excess, this can cause a range of health problems, including hearing impairment, sleep disturbance, and stress-related illnesses. To optimize the design of turbofan engines to reduce noise pollution and its correlating side effects, you can turn to acoustic modeling. Our jet pipe tutorial model speaks to the benefits of using such an approach.

Read More

Categories

Caty Fairclough | September 8, 2016

Rotating machinery is an important element in many structures, from wind turbines to engines. The analysis of this rotating machinery — a field known as rotordynamics — is key in reducing noise and vibrations in many areas of technology. Here, we’ll take a closer look at rotordynamics and its relevance within various applications.

Read More

Caty Fairclough | September 6, 2016

Refrigerated trucks must maintain a cool temperature in order to avoid damaging the products that they carry. Optimizing the insulation materials and cooling systems of these vehicles is therefore an important step in their design. To ensure that such components work effectively under open- and closed-door cycles, Air Liquide teamed up with SIMTEC, a COMSOL Certified Consultant, to perform heat transfer and CFD simulations with the COMSOL Multiphysics® software.

Read More

Temesgen Kindo | September 1, 2016

Suppose you take a piece of metal — a thin sheet, for example — and apply some mechanical loads. The metal will deform and take on a new shape that differs from the original undeformed configuration. Say you now want to use this deformed object as part of a new geometry construction. You can then solve another physics problem on the new composite domain. Today, we’ll demonstrate how to use a deformed object as an input to a geometry sequence.

Read More

Caty Fairclough | August 26, 2016

Around the world, trash is added to landfills at an increasingly rapid rate. Since these landfills take up large areas of land and can cause environmental issues, researchers are looking for safer, space-saving solutions. One option is to convert traditional anaerobic landfills into aerobic bioreactor landfills. This conversion process needs to be studied further, which could take years experimentally. For faster results, researchers at the University of Western Ontario used the COMSOL Multiphysics® software to efficiently analyze this process.

Read More

Beatrice Carasi | August 22, 2016

The numerical analysis of fluid flow and temperature fields can offer valuable insight in many engineering applications. Efficiency, of course, is important when performing such simulations. Here, we’ll discuss the various formulations for fluid flow equations in the COMSOL Multiphysics® simulation software and when it’s best to use each option, paying particular attention to how this selection influences heat transfer analyses. We will also cover how to set up both natural and forced convection simulations using these formulations.

Read More

Pawan Soami | August 17, 2016

Realistic gear geometries are useful for multibody dynamics simulations when coupled with other physical phenomena. Rather than manually building these geometries, we can use built-in parts available in the Part Library. With these highly parameterized gear parts, we can build a wide range of parallel and planetary gear trains and learn how to use different aspects of the built-in parts to create a realistic gear model in the Multibody Dynamics Module.

Read More

Bridget Cunningham | August 16, 2016

Like many crops, the quality of dates is heavily impacted by agronomic practices. In Tunisia, for example, such elements have caused these soft edible fruits to become drier in nature. One approach to improving the quality of these dates is thermal processing, where the key unit of operation is hydration. Combining the power of experimental studies with simulation analyses, a team of researchers sought to optimize the hydration process in order to foster greater efficiency and reliability.

Read More

Peng-Chhay Ung | August 15, 2016

The flash method, first described by W.J. Parker et. al in 1961, is a widely used technique for measuring the thermal conductivity of materials. Our Flash Method demo app, highlighted here, performs a numerical simulation of this experiment, offering a simplified approach to modifying parameters that can impact its overall accuracy. Today, we’ll take a closer look at this easy-to-use app, as well as the theory behind it.

Read More


Categories


Tags

1 2 3 4 28