Gaillard, N., Pinzelli, L., Gros-Jean, M., Bsiesy, A.
In recent years, a large variety of high dielectric constant materials has been studied as an alternative to silicon dioxide in order to improve the electrical properties in many integrated devices. The authors pointed out MIM electrical properties modifications such as current-voltage shift and the decrease in the voltage gap between the different conduction mechanisms voltage threshold while ...
Charles Stark Draper Laboratory
Micromechanical resonators are used in a wide variety of applications, including inertial sensing, chemical and biological sensing, acoustic sensing, and microwave transceivers. Despite the distinct design requirements for each of these applications, a ubiquitous resonator performance parameter emerges. This is the resonator’s Quality factor (Q), which describes the mechanical energy damping. ...
Kalavagunta, A., Weller, R.A.
Vanderbilt University, Nashville, TN
The four-point probe is a tool for measuring the resistivity of a material by contact with its surface. The tool is widely used in the semiconductor industry and has applications both in research and manufacturing. The method though is quite sensitive to various paramaters like the substrate material, probe separation, probe depth etc. In this paper we show that COMSOL multiphysics can be used ...
Finite-element Analysis of Properties in Real and Idealized Photonic Crystal Fibres, Application to Supercontinuum Generation
Gérôme, F., Viale, P., Tombelaine, V., Leproux, P., Auguste, J.L., Février, S., Blondy, J.M., Couderc, V.
IRCOM, CNRS UMR 6615, Limoges, France
Using a full-vector finite-element method, we calculate modal properties in index-guiding photonic crystal fibres. The influence of the deformation of the geometry in actual fibre structures is evaluated and compared to the idealized-model. These results are applied to the supercontinuum generation. Moreover, development of MATLAB softwares for FEMLAB 3.1 are presented.
Åberg, J., Vynnycky, M., Fredriksson, H.
KTH/Metallernas Gjutning, Stockholm, Sweden
This paper reports on progress in the implementation of COMSOL Multiphysics 3.2 to model thermal stresses in a three-dimensional solidifying shell, as occurs typically in the industrial continuous casting of copper, copper alloys and steel. Computer memory requirements prohibit a direct 3D numerical simulation of the temperature and the stresses. Instead, we use the fact that casting ...
Gamborg Andersen, G., Petrunin, V.V., Baurichter, A.
University of Southern Denmark, Physics Department, Odense, Denmark
We used FEMLAB (Finite Element Modelling LABoratory) for modelling heat propagation in 4 dimensions (time and the 3 spatial dimensions) after pulsed laser heating of non-isotropic materials during surface science experiments. As an example, the spatial and temporal evolution of a laser induced temperature jump in highly oriented pyrolytically grown graphite (HOPG) was calculated on a ns time ...
Zampolli, M., Tesei, A., Jensen, F.B.
NATO Undersea Research Centre, 19138 La Spezia, Italy
Acoustic waves are used in SONAR systems for the detection and classification of objects which may be swimming in the water column, proud on the seafloor, or buried below the sediment. In some applications, such as low frequency detection and classification of structurally complex objects immersed in a fluid, signal processing techniques must be aided by a-priori model based knowledge of the ...
Nestlé Waters Italy
Shelf life estimation is a very important issue in the beverage industry. Depending on the packaging application, estimation of the carbon dioxide loss through the plastic bottle walls has always been desirable and challenging at the same time. In this work an FEM approach is presented, which is shown to be able to replace time consuming, expensive lab tests. Gas permeability through the ...
Computational Dynamics Laboratory
Louisiana State University
Fluid and solute transport in hemodiafilter hollow fibers occurs through a non-trivial interaction of convection and diffusion, modulated by a number of factors that include the non-Newtonian behavior of blood, the density and viscosity dependence of blood on the local hematocrit and protein concentration, the Fahraeus-Lindquist effect on hematocrit, the osmotic effects of protein and partially ...
Electric Field Distribution in Biological Tissues for Various Electrode Configurations - A FEMLAB Study
Mitchell, W., Sundararajan, R.
Electronics & Computer Engineering Technology, Arizona State University, Mesa, AZ
Electroporation or Electropermeabilization (EP) is a non-viral physical process of inducing and/or increasing permeability of biological membranes by the application of high intensity and short duration electrical pulses. The resulting high field strength in the membrane can lead to the formation of regions of increased permeability, often called pores that allow transmembrane transport of ...