Join the Conversation - COMSOL Discussion Forum

Note that while COMSOL employees may participate in the discussion forum, COMSOL^® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

How to adjust scale of high aspect ratio object
read

2 Replies 116 Views

Version 6.2 Electromagnetics Results & Visualization Sujeong Lee posted 8 months ago 11 sept. 2024, 08:01 UTC−4 reply 8 months ago on 12 sept. 2024, 05:12 UTC−4 by Sujeong Lee
Adding damping layer in COMSOL
read

0 Replies 28 Views

Filippo Tosato posted 8 months ago 12 sept. 2024, 04:20 UTC−4
Two steps in one study
read

2 Replies 63 Views

Version 6.2 Aim FAR posted 8 months ago 11 sept. 2024, 09:30 UTC−4 reply 8 months ago on 11 sept. 2024, 11:17 UTC−4 by Aim FAR
How to localize the mode in the cantilever beam attached to a substrate and PML layer?
read

0 Replies 27 Views

Version 6.2 Structural & Acoustics Geometry Modeling Workflow Mohit Kumar posted 8 months ago 11 sept. 2024, 10:07 UTC−4
How to continue the study after stopped using livelink for matlab?
read

2 Replies 68 Views

General LiveLink for MATLAB Studies & Solvers HC L posted 9 months ago 23 juil. 2024, 05:32 UTC−4 reply 8 months ago on 10 sept. 2024, 22:14 UTC−4 by HC L
Visualization of Crack Tip Displacement for Applied Loads in 2D CZM Models
read

0 Replies 34 Views

Version 6.2 Results & Visualization Structural Mechanics Physics Interfaces Aida Bouaziz posted 8 months ago 10 sept. 2024, 19:15 UTC−4
Ring resonator with straight waveguide using EWFD interface
read

0 Replies 49 Views

Version 6.2 Wave Optics Physics Interfaces Raonaqul Islam posted 8 months ago 10 sept. 2024, 13:45 UTC−4
Defining contact for a large number of surfaces
read

3 Replies 105 Views

Structural & Acoustics Structural Mechanics Structural Dynamics FDZR posted 8 months ago 5 sept. 2024, 12:56 UTC−4 reply 8 months ago on 10 sept. 2024, 10:49 UTC−4 by Henrik Sönnerlind
adding mass and inertia
read

9 Replies 129 Views

Filippo Tosato posted 8 months ago 6 sept. 2024, 04:12 UTC−4 reply 8 months ago on 10 sept. 2024, 04:47 UTC−4 by Filippo Tosato
Failed to find a solution for the initial parameter. Out of memory during LU factorization. Returned solution is not converged. Not all parameter steps returned.
read

1 Replies 102 Views

Version 6.1 逸鑫高 posted 8 months ago 9 sept. 2024, 05:44 UTC−4 reply 8 months ago on 9 sept. 2024, 09:35 UTC−4 by Robert Koslover

Premier

621–630 of 37417

Dernier

Discussion Forum

Topic

Versions

How to adjust scale of high aspect ratio object

Adding damping layer in COMSOL

Two steps in one study

How to localize the mode in the cantilever beam attached to a substrate and PML layer?

How to continue the study after stopped using livelink for matlab?

Visualization of Crack Tip Displacement for Applied Loads in 2D CZM Models

Ring resonator with straight waveguide using EWFD interface

Defining contact for a large number of surfaces

adding mass and inertia

Failed to find a solution for the initial parameter. Out of memory during LU factorization. Returned solution is not converged. Not all parameter steps returned.