Articles techniques et présentations

Recherche rapide

Ressources

Livres Blancs

À la conférence COMSOL 2025, des ingénieurs, des chercheurs et des scientifiques du monde entier ont présenté leur utilisation de la modélisation et de la simulation dans tous les grands secteurs d'activité et dans le monde universitaire. Utilisez l'outil de recherche rapide pour trouver une présentation spécifique ou filtrez par sujet ou par lieu d'événement.

ISBN: 978-1-7364524-3-1

Terme recherché:

2009 - Boston

Stress Field Simulation for Quantitative Ultrasound Elasticity Imaging

L. Yuan[1] and P.C. Pedersen[1]
[1]Department of Electrical and Computer Engineering, Worcester Polytechnic Institute, Worcester, Massachusetts, USA

Finite element models using COMSOL Multiphysics and MATLAB were developed to solve the problem of stress distribution interior homogeneous, isotropic, incompressible elastic solid material under known vertical external compression with a rectangular contact surface. Moreover, comparison ... En savoir plus

Study of Fluid and Mass Adsorption Model in the QCM-D Sensor for Characterization of Biomolecular Interaction

H.J. Kwon[1], C.K. Bradfield[1], B.T. Dodge[1], and G.S. Agoki[1]
[1]Department of Engineering and Computer Science, Andrews University, Berrien Springs, Michigan, USA

Increasing attention has been paid to application of the quartz crystal microbalance with dissipation (QCM-D) sensor for monitoring biomolecular interactions. This paper focuses on a practical application of protein-protein binding affinity measurement at low concentrations and minimal ... En savoir plus

The Effect of a Correlated Surface Roughness and Convection on Heat Conduction

A.F. Emery[1]
[1]Department of Mechanical Engineering, University of Washington, Seattle, Washington, USA

Heat conduction through a slab, 0 ≤ x ≤ W is one dimensional. However, if one of the edges, say x=0, is rough the conduction will be two dimensional. The two dimensionality varies with the correlation length with a maximum at a length approximately 10% of the slab width. ... En savoir plus

Viscous damping of a periodic perforated MEMS microstructure when the Reynolds’ equation cannot be applied: Numerical simulations

D. Homentcovschi[1], and R.N. Miles[1]
[1]Department of Mechanical Engineering, SUNY Binghamton, NY

This paper develops a computational model for determining the total damping coefficient for a unit cell of a MEMS microscale device containing a repetitive pattern of holes. The basic cell of the microstructure is approximated by an axi-symmetric domain and the velocity and pressure ... En savoir plus

Importance of Assembly Discontinuity Factors In Simulating Reactor Cores Containing Highly Heterogeneous Fuel Assemblies

G. Gomes[1]
[1]Atomic Energy of Canada Limited, Mississuaga, Ontario, Canada

To assess the importance of assembly discontinuity factors (ADF), a highly heterogeneous reactor core was simulated using a COMSOL model in which ADF are not used. The resulting errors in assembly powers were found to be unacceptably high. This indicates that for highly heterogeneous ... En savoir plus

Expanding Your Materials Horizons

R. Pryor[1]
[1]Pryor Knowledge Systems, Inc. (COMSOL Certified Consultant), Bloomfield Hills, Michigan, USA

Materials and their related properties are intrinsically fundamental to the creation, development and solution of viable exploratory models when using numerical analysis software. In many cases, simply determining the location, availability and relative accuracy of the necessary material ... En savoir plus

A Study of Lubricating Flows in MEMS Bearings

E. Gutierrez-Miravete[1], and J. Streeter[2]

[1]Department of Engineering and Science, Rensselaer at Hartford, Hartford, Connecticut, USA
[2]Optiwind, Torrington, Connecticut, USA

The bearing and shaft are part of a safe and arm device constructed as an assembly by a multi-layer additive/subtractive plating and planarization processes (EFAB technology). Devices are constructed by a multi-layer additive/subtractive planarization process. This paper evaluates the ... En savoir plus

Wireless Interaction of Neighboring Two Arm Archimedes Spiral Coils in the RF Electromagnet Range

A. Kalinowski[1]
[1]Naval Undersea Warfare Center/ Division Newport, Newport, RI, USA

The paper addresses a class of problems for modeling and consequently simulating the electromagnetic field radiation pattern from two arms Archimedes spiral coils. The frequency spatial wavelengths relative to the coil dimensions are in a range where the electromagnetic Maxwell’s ... En savoir plus

Finite Element Analysis of an Enzymatic Biofuel Cell: The Orientations of a chip inside a blood artery

C. Wang[1], Y. Parikh[1], Y. Song[1], and J. Yang[1]
[1]Mechanical & Materials Science Engineering, Florida International University, Miami, Florida, USA

Output performance of an implantable enzymatic biofuel cell (EBFC) with three- dimensional highly dense micro-electrode arrays has been simulated with a finite element analysis approach. The purpose of this research is to optimize the orientation of this EBFC chip inside a blood artery ... En savoir plus

Modeling Flow of Magnetorheological Fluid through a Micro-channel

N.M. Bruno[1], C. Ciocanel[1] and A. Kipple[2]
[1]Department of Mechanical Engineering, Northern Arizona University, Flagstaff, Arizona, USA
[2]Dept. of Electrical Engineering and Computer Sciences, Northern Arizona University, Flagstaff, Arizona, USA

This paper presents the approach taken through the utilization of COMSOL Multiphysics 3.5a, to develop a model that simulates the flow of a magnetorheological (MR) fluid through a micro-channel. The model was developed as an aid in the analysis of a micropump that produces flow by means ... En savoir plus

Premier

111–120 of 130

Dernier

Articles techniques et présentations

Recherche rapide

COMSOL Conference 2025 Proceedings

Collection of Papers, Posters, and Slideshows Accepted by the Program Committee