Articles techniques et présentations

Recherche rapide

Ressources

Livres Blancs

Voyez comment la modélisation et la simulation sont utilisées par les industries La modélisation et la simulation multiphysiques pilotent l'innovation dans tous les grands secteurs d'activité et dans le monde universitaire — comme en témoignent les nombreuses utilisations présentées dans des articles et des posters techniques présentés par des ingénieurs, chercheurs et scientifiques à la Conférence COMSOL chaque année. Inspirez-vous des récents proceedings réunis ci-dessous, ou, pour trouver les présentations les plus intéressantes dans votre domaine d'intérêt, utilisez la recherche rapide.

Consultez les proceedings de la Conference COMSOL 2024

Terme recherché:

Computational Fluid Dynamics

Performance Prediction of Eddy Current Flowmeter for Sodium

P. Sharma[1], S. K. Dash[1], B. K. Nashine[1], S. S. Kumar[1], R. Veerasamy[1], B. Krishnakumar[1], P. Kalyanasundaram[1], and G. Vaidyanathan[1]
[1] Fast Reactor Technology Group, Indira Gandhi Centre for Atomic Research, Kalpakkam, Tamil Nadu

Sodium is used as a coolant in Fast Breeder Reactors. Eddy Current Flowmeter (ECFM) is used for measurement of sodium flow in the primary pump and at the outlet of the subassemblies. Eddy Current Flowmeter (ECFM) works on the principle of change in the magnetic field profile due to ... En savoir plus

Sensitivity Estimation of Permanent Magnet Flowmeter

V. Sharma[1], S. K. Dash[1], G. Vijaykumar[1], B. K. Nashine[1], B. Krishnakumar[1], P. Kalyanasundaram[1], and G. Vaidyanathan[1]
[1]Fast Reactor Technology Group, Indira Gandhi Centre for Atomic Research, Kalpakkam, Tamil Nadu, India

Permanent Magnet Flowmeter (PMFM) is a non invasive device, which is used to measure the flow of electricallyconducting sodium in Fast Breeder Reactor Circuits. PMFM works on the principle of generation of motional EMF by magnetic forces exerted on the charges in a moving conductor. In ... En savoir plus

Newtonian and Non-Newtonian Blood Flow over a Backward-Facing Step: Steady-State Simulation

M.W. Siebert[1], and P.S. Fodor[1]
[1]Physics Department, Cleveland State University, Cleveland, Ohio, USA

In this work, the fluid flow over a 2D backward-facing step is analyzed in order to provide a case study for the use of different models for the blood dynamic viscosity in COMSOL Multiphysics. Three non-Newtonian models, as well as the Newtonian model are used to study the shear stresses ... En savoir plus

Reliability Evaluation for Static Chamber Method at Landfill Sites

H. Ishimori[1], K. Endo[1], and M. Yamada[1]
[1]National Institute for Environmental Studies, Tsukuba, Ibaraki, Japan

In this study, COMSOL Multiphysics was used for the reliability evaluation for static chamber method at landfill sites. Static chamber method, which measures landfill gas emission fluxes, is widely used at landfill sites for the monitoring of greenhouse gas emission such as methane and ... En savoir plus

Reynolds Number Dependent Porous Media Flow Using the Brinkman Equation

R. Rieck[1], A. Bénard[1], and C. Petty[1]
[1]Michigan State University, Michigan, USA

Porous media fluid dynamic modeling has been widely explored and utilized in many academic and industrial applications. Cross flow filtration being one attractive application, whereas the fluid and filtrate flow parallel the porous media, and thereby induce shearing stress along the ... En savoir plus

Two-Phase Modeling of Gravity Drainage of Bitumen from Tar Sand Using In-Situ RF Electrical Heating

A. Hassanzadeh
Pyrophase Inc., Chicago, IL, USA

In-situ electrical heating technologies are among the most recent technologies used for bitumen recovery from tar sand and oil shale. These technologies have limited environmental impact because there is little disturbance of the land, and water and solvents are not used. Two-phase ... En savoir plus

Analysis of Ancient Natural Ventilation Systems inside the Pitti Palace in Florence

C. Balocco
Dipartimento di Energetica “Sergio Stecco”, Università degli Studi di Firenze, Firenze, Italy

This paper presents and discusses the first phase results of a wide ranging project concerning the study and prediction of the efficiency and energy performances of natural ventilation systems existing inside historic buildings. The air flow patterns, air temperature and air velocity ... En savoir plus

Validation of DNS Techniques for Dynamic Combined Indoor Air and Constructions Simulations Using an Experimental Scale Model

T. van Goch, and A. van Schijndel
Eindhoven University of Technology, Eindhoven, Netherlands

This paper presents a study on the application of Direct Numerical Solving (DNS) techniques using an experimental scale model. COMSOL Multiphysics is promising in solving dynamic heat and air transport. The experiments can be extremely useful as benchmark for CFD codes. En savoir plus

Fully Coupled Thermo-Hydro-Mechanical Modeling by COMSOL Multiphysics, with Applications in Reservoir Geomechanical Characterization

T. Freeman[1], R. Chalaturnyk[1], and I. Bogdanov[2]
[1]University of Alberta, Edmonton, AB, Canada
[2]Centre Huile Lourde Ouvert et Expérimental (CHLOE), France

Because of the complex nature of geomaterials and presence of solid and fluid within a single system, it is crucial to consider all the physics involved within the geomaterial system. A fully coupled thermo-hydromechanical model is developed. The model consists of a three-phase flow ... En savoir plus

Numerical Simulations of Spherical Gap Flows

K. Buehler, and J. W. Louw
University of Applied Sciences Offenburg, Germany

Rotating fluids are important in nature and technology. Many applications can be found in the field of meteorology and in rotating machinery. This investigation concerns the application of the swirl flow application mode in COMSOL Multiphysics to simulate nonlinear aspects of flows ... En savoir plus

Premier

911–920 of 1091

Dernier