Articles techniques et présentations

Recherche rapide

Ressources

Livres Blancs

Ici vous trouverez les présentations issues des Conférences COMSOL à travers le monde. Réalisées par des utilisateurs de COMSOL Multiphysics, ces présentations explorent tous les domaines actuels d'innovation. Les applications couvrent pratiquement tous les secteurs industriels et impliquent des phénomènes électriques, mécaniques, fluidiques et chimiques. Utilisez la recherche rapide pour trouver les présentations les plus intéressantes dans votre domaine d'intérêt.

Consultez les proceedings de la Conference COMSOL 2024

Terme recherché:

Modelling of Seismoelectric Effects

B. Kröger[1], U. Yaramanci[2], and A. Kemna[1]
[1]1 University of Bonn
[2]GGA Hannover

We present the results of full-waveform time-dependent finite-element modelling of coupled seismoelectromagnetic wave propagation in fluid-saturated porous media. To describe the seismoelectric response of the system a new set of equations is developed which couple the poroelasticity ... En savoir plus

Extraction of Electrical Equivalent Circuit of One Port SAW Resonator Using FEM-based Simulation

A. K. Namdeo [1], H. B. Nemade [1],
[1] Department of Electronics and Electrical Engineering, Indian Institute of Technology Guwahati, Guwahati, Assam, India

The paper presents a method of extraction of electrical equivalent circuit of a one port surface acoustic wave (SAW) resonator from the results of simulation based on finite element method (FEM) using COMSOL Multiphysics software. A one port SAW resonator consists of large number of ... En savoir plus

Simulation of Acoustical Transfer Paths for Active Noise Control

L. Fromme [1], J. Waßmuth [1], D. Wehmeier [1],
[1] Bielefeld University of Applied Sciences, Bielefeld, Germany

The knowledge of the acoustical transfer paths in active noise control systems is very important for the performance of the system. Unfortunately, simulation is challenging since even simple configurations require comprehensive experience in physics and modeling. Two test setups were ... En savoir plus

Finite Element Analysis into Eigenfrequencies of a Total Hip Stem with Different Levels of Loosening

T. Bender [1], M. Sass [1], W. Mittelmeier [1], R. Bader [1], D. Kluess [1]
[1] Department of Orthopaedics Research Laboratory for Biomechanics & Implant Technology, University Medicine Rostock, Rostock, Germany

A finite element model of a total hip replacement (THR) has been developed from the approach of modal analysis. The model is capable of determining the first 15 Eigenmodes of a THR with an artificial bone model. The model was equipped with several different defects to simulate a ... En savoir plus

Modal Analysis of Rotating Machines

C. Frankrone [1], L. Fromme [1],
[1] Department of Engineering Sciences and Mathematics, Bielefeld University of Applied Sciences, Bielefeld, Germany

Machines with rotating components are prone to vibrations because an imbalance of the rotor would always act as a harmonic excitation force to the machine. Thus oscillations close to the natural frequencies are tried to pass through fast in the run-up and cast-down or even completely ... En savoir plus

Modeling, Simulation, and Optimization of Piezoelectric Bimorph Transducer for Broadband Vibration Energy Harvesting in Multi-Beam and Trapezoidal Approach

N. Chen [1], V. Bedekar [1],
[1] Department of Engineering Technology, Middle Tennessee State University, Murfreesboro, TN, USA

The objective of the research is to design a broadband energy harvester device through the multi-beam approach and non-linear trapezoidal geometry approach. The performance of two piezoelectric PZT-PZN polycrystalline ceramic composition samples are simulated in COMSOL Multiphysics®, and ... En savoir plus

The Role of COMSOL Toward a Low-Enriched Uranium Fuel Design for the High Flux Isotope Reactor

J.D. Freels[1]
[1]Oak Ridge National Laboratory, Oak Ridge, Tennessee, USA

Design and safety analyses are underway to convert the High Flux Isotope Reactor (HFIR) at the Oak Ridge National Laboratory (ORNL) from a high-enriched uranium (HEU) fuel to a low-enriched uranium (LEU) fuel. The primary constraint for the project is that the overall fuel plate ... En savoir plus

Simple Disk Piezo Transformer Based Oscillator

J. P. Sandoz[1], J. M. Kissling[1]
[1]Institute of Applied Microtechnology, La Chaux-de-Fonds, HE‐ARC, Switzerland

In this contribution we present a COMSOL Multiphysics® example of a disk piezoelectric ceramic transformer (D-PT) coupled with a bipolar NPN transistor to form an auto-oscillator. The comparison between the simulations and the measurements made on our prototype are found to be in good ... En savoir plus

Development of a Package for a Triaxial High-G Accelerometer Optimized for High Signal Fidelity

R. Langkemper [1], R. Külls [1], J. Wilde [2], S. Nau [1], S. Schopferer [1],
[1] Fraunhofer-Institut für Kurzzeitdynamik, Ernst-Mach-Institut, EMI, Freiburg, Germany
[2] Albert-Ludwigs-Universität Freiburg, Institut für Mikrosystemtechnik, Freiburg, Germany

Acceleration is an important quantity to be measured in high-speed dynamics. A new piezoresistive sensor for the measurement of high-amplitude, short-duration transient accelerations of up to 100,000 g has been developed at the Fraunhofer EMI. Its figure of merit (sensitivity x resonance ... En savoir plus

Extraction of 13.56 MHz NFC-Reader Antenna Parameters for Matching Circuit Design

Prof. Dr.-Ing. habil. A. K. Palit [1],
[1] ZF-Lemfoerder Electronic GmbH, ZF-Friedrichshafen AG. Group, Espelkamp, Germany

Introduction: RFID system uses a Transponder and the near field communication (NFC) antenna and a matching circuit (Figure-1) in which at least latter two must be optimally designed for a higher efficiency. Typically, RFID antennas are flat inductive coils with 2 to 4 turns and are ... En savoir plus

Premier

161–170 of 352

Dernier