Articles techniques et présentations

Recherche rapide

Ressources

Livres Blancs

Voyez comment la modélisation et la simulation sont utilisées par les industries La modélisation et la simulation multiphysiques pilotent l'innovation dans tous les grands secteurs d'activité et dans le monde universitaire — comme en témoignent les nombreuses utilisations présentées dans des articles et des posters techniques présentés par des ingénieurs, chercheurs et scientifiques à la Conférence COMSOL chaque année. Inspirez-vous des récents proceedings réunis ci-dessous, ou, pour trouver les présentations les plus intéressantes dans votre domaine d'intérêt, utilisez la recherche rapide.

Consultez les proceedings de la Conference COMSOL 2024

Terme recherché:

Effect of S-p Relation Model on DNAPL Migration Simulation Result

H. Ishimori[1], and K. Endo[1]
[1]National Institute for Environmental Studies, Tsukuba, Ibaraki, Japan

To consider effective counter measures against ground water contaminated with dense non-aqueous phase liquids (DNAPLs) such as chlorinated solvents, it is first important to understand the mechanism of their migration in heterogeneous aquifer. In addition, numerical analysis models to ... En savoir plus

Modeling Ion Motion in a Miniaturized Ion Mobility Spectrometer

S. Barth, and S. Zimmermann
Drägerwerk AG & Co. KGaA, Lübeck, Germany

Ion mobility spectrometry provides fast detection of very low concentrations of chemical substances. Simple instrumentation combined with high sensitivity and high selectivity are the advantages of this technique. One well established field of application is the detection of hazardous ... En savoir plus

Design of a RF MEMS Switch

B. Mishra, M. P. S. Naidu, J. Raj, and Z. C. Alex
VIT University
Vellore
Tamilnadu, India

This paper presents a novel design of a RF MEMS Switch. The switch is a capacitive type, which is actuated by an electrostatic force. The structure of the switch consists of a CPW (coplanar waveguides) transmission lines and a suspended membrane. The modelling of switch is done using ... En savoir plus

Designing Polymer Thick Film Intracranial Electrodes for use in Intra-Operative MRI Setting.

G. Bonmassar[1], and A. Golby[2]
[1]AA. Martinos Center, Massachusetts General Hospital, Charlestown, Massachusetts, USA
[2]Department of Neurosurgery, Brigham and Women’s Hospital, Boston, Massachusetts, USA

A new type of MRI compatible intracranial electrode based on Polymer Thick Film (PTF) is presented and studied using COMSOL Multiphysics. The geometry considered was a two-dimensional cross section cut of 5 mm thick electrodes with 5 cm leads on top of a 2×10 cm slab representing ... En savoir plus

PCCP Profiling and Tube Wave Analysis of WRE Signal

N. Chowdhury[1], Z. Liao[2], and L. Zhao[1]
[1]Department of Electrical & Computer Engineering, Ryerson University, Toronto, ON, Canada
[2]Department of Architectural Science, Ryerson University, Toronto, ON, Canada

Acoustic wave propagation due to the breakage or slippage of reinforced wire in water-filled prestressed concrete cylinder pipe (PCCP) attracts interest in non-destructive pipe testing. Current practice of acoustic emission (AE) detection and wire-break related events (WRE) recognition ... En savoir plus

Simulation of Acoustical Transfer Paths for Active Noise Control

L. Fromme [1], J. Waßmuth [1], D. Wehmeier [1],
[1] Bielefeld University of Applied Sciences, Bielefeld, Germany

The knowledge of the acoustical transfer paths in active noise control systems is very important for the performance of the system. Unfortunately, simulation is challenging since even simple configurations require comprehensive experience in physics and modeling. Two test setups were ... En savoir plus

Finite Element Simulation of Love Wave based SAW Delay Line Using COMSOL Multiphysics

S. Trivedi [1], H. B. Nemade [2],
[1] Center for Nanotechnology, Indian Institute of Technology Guwahati, Guwahati, Assam, India
[2] Department of Electronics and Electrical Engineering, Indian Institute of Technology Guwahati, Guwahati, Assam, India

The paper presents 3D finite element simulation of Love wave based SAW delay line using COMSOL Multiphysics software. The device consists of a 36° YX Lithium Tantalate substrate covered with 4.7 μm thick SiO2 waveguide layer operating at λ = 12 μm. Time response study is used to ... En savoir plus

Extraction of Electrical Equivalent Circuit of One Port SAW Resonator Using FEM-based Simulation

A. K. Namdeo [1], H. B. Nemade [1],
[1] Department of Electronics and Electrical Engineering, Indian Institute of Technology Guwahati, Guwahati, Assam, India

The paper presents a method of extraction of electrical equivalent circuit of a one port surface acoustic wave (SAW) resonator from the results of simulation based on finite element method (FEM) using COMSOL Multiphysics software. A one port SAW resonator consists of large number of ... En savoir plus

Finite Element Analysis into Eigenfrequencies of a Total Hip Stem with Different Levels of Loosening

T. Bender [1], M. Sass [1], W. Mittelmeier [1], R. Bader [1], D. Kluess [1]
[1] Department of Orthopaedics Research Laboratory for Biomechanics & Implant Technology, University Medicine Rostock, Rostock, Germany

A finite element model of a total hip replacement (THR) has been developed from the approach of modal analysis. The model is capable of determining the first 15 Eigenmodes of a THR with an artificial bone model. The model was equipped with several different defects to simulate a ... En savoir plus

RF Emission Spectra in Laser-Plasma Acceleration of Protons

M. Seimetz [1],
[1] Instituto de Instrumentación para Imagen Molecular (I3M), CSIC-Universitat Politècnica de València, Spain

The acceleration of protons and ions by highly intense, ultra-short laser pulses is a very active field of experimental and theoretical research. From laser-plasma interactions the emission of a strong electromagnetic pulse (EMP) has often been reported as a side effect. It potentially ... En savoir plus

Premier

161–170 of 363

Dernier