Articles techniques et présentations

Recherche rapide

Ressources

Livres Blancs

Voyez comment la modélisation et la simulation sont utilisées par les industries La modélisation et la simulation multiphysiques pilotent l'innovation dans tous les grands secteurs d'activité et dans le monde universitaire — comme en témoignent les nombreuses utilisations présentées dans des articles et des posters techniques présentés par des ingénieurs, chercheurs et scientifiques à la Conférence COMSOL chaque année. Inspirez-vous des récents proceedings réunis ci-dessous, ou, pour trouver les présentations les plus intéressantes dans votre domaine d'intérêt, utilisez la recherche rapide.

Consultez les proceedings de la Conference COMSOL 2024

Terme recherché:

Numerical Study of Microfluidic Fuel Cell Performance

A. E. Khabbazi[1], A.J. Richards[1], and M. Hoorfar[1]
[1]School of Engineering, UBC Okanagan, Kelowna, BC Canada, Canada

Using COMSOL Multiphysics 3.5, a numerical model has been developed to determine the effect of the channel geometry and electrode configuration on cell performance based on polarization curves. The Butler-Volmer equation was implemented to determine the reaction rates at the electrodes. ... En savoir plus

Modelling and Simulating CO2 Electro-Reduction to Formic Acid using MEC- Microfluidic Electrolytic Cells

A. Offong[1], V. Manovic[1], E. Anthony[1]
[1]Cranfield University, United Kingdom

Model calibration and validation were implemented using experimental data from literature. We utilized a microfluidic electrochemical cell that was configured with parallel, rectangular, and multi-layered channels, which is operating in a co-flow mode. CO2 gas stream enters the cathode ... En savoir plus

Electrical Energy Harvesting from Body Heat: Indirect Conversion via Mechanical Vibration

S. Shin [1], H. Mojtaba [1], F. Ayazi [1],
[1] Georgia Institute of Technology, Atlanta, GA, USA

Recent rapid progress in MEMS with wireless communication system has enabled low power micro sensor network for human body, Body Area Sensor Network (BASN). The information gathering from BASNs will provide a significant opportunities for various medical applications. One of the key ... En savoir plus

Simulations of Polymer Based Micro Heater Operated at Low Voltage

M. Gayake[1], D. Bodas[2], and S. A. Gangal[1]
[1]Department of Electronic science, University of Pune, India
[2]Centre for Nanobioscience, Agharkar Research Institute, India

This paper presents a design of polymer based micro heater operating in the temperature range of 200- 250°C which could be operated at low voltage (battery operated). The micro heater has been designed and simulated using COMSOL 4.1, FEM simulation tool. Simulation was performed for ... En savoir plus

Optimization of the Lithium Insertion Cell with Silicon Negative Electrode for Automotive Applications

R. Chandrasekaran, and A. Drews
Research and Advanced Engineering
Ford Motor Company
Dearborn, MI

The US Advanced Battery Consortium (USABC) has established goals for long term commercialization of advanced batteries for electric vehicle applications. In this work, a dual lithium-ion insertion cell with silicon as the negative electrode and an intercalation material as the positive ... En savoir plus

Analysis and Design of Antennas for an Implantable Medical Device System for Functional Electrical Stimulation

H. Suri[1]
[1]Alfred Mann Foundation for Scientific Research, Valencia, CA, USA

This poster outlines the results of finite element analyses to study the antenna radiation pattern of an implanted medical device. Also presented are simulation results used to design an electrically small antenna for a portable control unit that communicates with the implants over the ... En savoir plus

Finite element analysis approach for optimization of enzyme activity for enzymatic bio-fuel cell

C. Wang[1], Y. Song[1], Y. Parikh[1], and J.H. Yang[1]
[1]Department of Mechanical & Materials Science Engineering, Florida International University, Miami, Florida, USA

Enzymatic biofuel cells (EBFCs) are miniature implantable power sources, which use enzymes as catalysts to perform redox reaction with biological fuels such as glucose. In this study, we focused on a three dimensional EBFC chip with highly dense micro-electrode arrays, fabricated by ... En savoir plus

Numerical Modeling of a Serpentine Channel SOFC for Elevated Pressure Applications

Nayan Biswas [1], Deepra Bhattacharya [2], Manoj Kumar [1], Jayanta Mukhopadhyay [2], Rajendra Nath Basu [2], Prasanta Kumar Das [1],
[1] Indian Institute of Technology Kharagpur, Kharagpur, West Bengal, India
[2] Central Glass and Ceramic Research Institute, Kolkata, West Bengal, India

Solid oxide fuel cell (SOFC) is a kind of high-temperature fuel cell which directly converts the chemical energy of the fuel into the electrical energy. The high efficiency and fuel flexibility of the SOFC has widened its applications in the field of energy. In the present study, a 3-D ... En savoir plus

COMSOL Multiphysics{:sup}®{:/sup} Version 4

COMSOL Multiphysics^® Version 4

Svante Littmarck
President and CEO, COMSOL

Svante Littmarck is the CEO of the COMSOL group. He co-founded COMSOL in 1986. He holds a M.Sc. in Applied Mathematics from the Royal Institute of Technology in Stockholm. In 2004 he received an honorary doctoral degree from the Royal Institute of Technology. En savoir plus

Two-Dimensional Simulation of All-Solid-State Lithium-ion Batteries

L. Tong [1],
[1] Keisoku Engineering System Co., Ltd., Chiyoda-ku, Tokyo, Japan

There is great interest in developing all-solid-state lithium-ion batteries. They are ideal micro-power sources for many applications in portable electronic devices, electric vehicles and biomedical engineering. It is known that all-solid-state lithium-ion batteries are often fabricated ... En savoir plus

Premier

171–180 of 249

Dernier