Articles techniques et présentations

Recherche rapide

Ressources

Livres Blancs

Voyez comment la modélisation et la simulation sont utilisées par les industries La modélisation et la simulation multiphysiques pilotent l'innovation dans tous les grands secteurs d'activité et dans le monde universitaire — comme en témoignent les nombreuses utilisations présentées dans des articles et des posters techniques présentés par des ingénieurs, chercheurs et scientifiques à la Conférence COMSOL chaque année. Inspirez-vous des récents proceedings réunis ci-dessous, ou, pour trouver les présentations les plus intéressantes dans votre domaine d'intérêt, utilisez la recherche rapide.

Consultez les proceedings de la Conference COMSOL 2024

Terme recherché:

Analysis of Heat, Mass Transport, and Momentum Transport Effects in Complex Catalyst Shapes for Gas-Phase Heterogeneous Reactions Using COMSOL Multiphysics

A. Nagaraj[1], and P. Mills[2]

[1]Department of Electrical Engineering and Computer Science, Texas A&M University, Kingsville, TX, USA
[2]Department of Chemical and Natural Gas Engineering, Texas A&M University, Kingsville, TX, USA

The global demand for sulfuric acid has been forecast to grow at an average of 2.6% per year from 2005 – 2010. The primary objective of this work is to analyze the performance of various heterogeneous catalyst shapes that have been proposed for the oxidation of SO2 to SO3 used in the ... En savoir plus

Numerical Analysis for Surface Discharge on Solid Insulation in the Dielectric Liquid with Experimental Validation

H.-Y. Lee, S.-H. Lee [1]
[1] Kyungpook National University, Daegu, Korea

Surface discharge initiation and propagation on the surface of an insulating solid immersed in a dielectric liquid were examined numerically and experimentally. To establish a generalized numerical technique for evaluating surface discharge phenomena using the electrohydrodynamics (EHD) ... En savoir plus

Modeling of Radial Source Flow in Porous Media: Miscible Viscous Fingering Patterns

V. Sharma [1], S. Pramanik [2], M. Mishra [1],
[1] Indian Institute of Technology Ropar, Rupnagar, India
[2] Indian Institute of Technology Ropar, Rupnagar, India; Nordita, SE-10691 Stockholm, Sweden.

COMSOL Multiphysics® software was used to model radial source flow in two dimensional homogeneous porous media. Two-Phase Darcy's Law (tpdl) is used to model miscible viscous fingering. Fingering patterns obtained on using different mesh are discussed. Evolution from 'flowers' to ... En savoir plus

Enhanced Fin Tube Heat Exchanger Design Through Topology Optimization

Shi Zeng [1],
[1] National University of Singapore, Singapore

Fin tube heat exchangers are widely used in air conditioning systems. Various fin structures have been proposed and studied in literature to enhance their heat transfer performance. However, enhancement in heat transfer is often accompanied by pressure drop penalty. This study utilized a ... En savoir plus

Modeling Wear of Journal Bearings

P. Bergmann [1], F. Grün [1],
[1] Chair of Mechanical Engineering, Montanuniversität Leoben, Leoben, Austria

Wear in hydrodynamic journal bearings resulting from solid contact in the mixed friction regime becomes an increasingly prominent topic leading to the necessity of numerical wear evaluations. A numerical method tackling this topic based on Archard’s wear law is presented and applied on a ... En savoir plus

Implementation of a Thermo-Hydrodynamic Model to Predict the Morton Effect

M. Antonini [1], D. Fausti [1], M. Mor [1],
[1] PoliBrixia s.r.l., Brescia, Italy

In this paper, the "Morton Effect" is analyzed. This phenomenon is a particular kind of rotor instability due to non-uniform journal bearing heating. In this paper, an overview of the previous works has been done. After this preliminary study, a specific approach suggested by the ... En savoir plus

Numerical Analysis of Heat Generation in Ball End Magnetorheological Finishing

H. Garg [1], P. K. Baghel [1], S. Kumar [1], A. S. Kharola [1]
[1] CSIR - Central Scientific Instruments Organisation, Chandigarh, India

In the Ball End Magneto rheological Finishing, due to heat generation by thermal agitation the effect of MRF finishing reduces and this ultimately hampers the process of the precision finishing and density of MR fluid too, which therefore results in instability of MR fluid. En savoir plus

Modelling Heat and Mass Transfer in Microreactor for Methanol to Hydrocarbons

P. A. Delou [1,3], V. Degirmenci [2,3],
[1] Universidade Federal do Rio de Janeiro, Rio de Janeiro, RJ, Brazil
[2] University of Warwick, Coventry, United Kingdom
[3] Queen’s University Belfast, Belfast, United Kingdom

Recently, increasing availability of natural gas, due to the shale gas, raises the attention to the conversion of methane. Methanol-to-Hydrocarbons reaction (MTH) plays an important role in this route where methanol synthesized through syngas is converted into hydrocarbons, such as ... En savoir plus

Numerical Simulation of Electrostatic Charging Droplets in Microfluidic Devices

S. Yao[1], H. Zhou[1]
[1]HKUST, Hong Kong, China

In this paper, the mechanism of charging process was simulated and analyzed. The simulation was conducted using COMSOL Multiphysics® software, based on the laminar two-phase flow level-set interface coupling with the electrostatic interface. Meanwhile, different parameters (such as the ... En savoir plus

Uncertainty Quantification: What it is and Why it is Important for Multiphysics Simulations

P. Qian [1, 2],
[1] University of Wisconsin - Madison, Madison, WI, USA
[2] SmartUQ, Madison, WI, USA

Uncertainty appears in many aspects of physical simulations including stochastic design parameters, hard-to-specify input distributions, probabilistic boundary and initial conditions, and unknown geometries. Uncertainty Quantification (UQ) has emerged as the science of quantitative ... En savoir plus

Premier

221–230 of 385

Dernier