Articles techniques et présentations

Recherche rapide

Ressources

Livres Blancs

Voyez comment la modélisation et la simulation sont utilisées par les industries La modélisation et la simulation multiphysiques pilotent l'innovation dans tous les grands secteurs d'activité et dans le monde universitaire — comme en témoignent les nombreuses utilisations présentées dans des articles et des posters techniques présentés par des ingénieurs, chercheurs et scientifiques à la Conférence COMSOL chaque année. Inspirez-vous des récents proceedings réunis ci-dessous, ou, pour trouver les présentations les plus intéressantes dans votre domaine d'intérêt, utilisez la recherche rapide.

Consultez les proceedings de la Conference COMSOL 2024

Terme recherché:

Numerical Modelling of Vortex Induced Vibrations in Submarine Pipelines

F. Van den Abeele, J. Vande Voorde, and P. Goes
ArcelorMittal Research & Development Industry Gent, Zelzate, Belgium

Vortex-induced vibration is a major cause of fatigue failure in submarine oil and gas pipelines and steel catenary risers. Even moderate currents can induce vortex shedding. In this paper, COMSOL Multiphysics is applied to study the flow pattern around submarine pipeline spans, and ... En savoir plus

Computational Study on Transition of Oil-Water Flow Morphology due to Sudden Contraction in Microfluidic Channel

J. Chaudhuri[1], S. Timung[1], T. K. Mandal[1], D. Bandyopadhyay[1]
[1]Indian Institute of Technology Guwahati, Guwahati, Assam, India

The flow morphology of two immiscible fluids in a microfluidic device finds numerous applications such as emulsification, synthesis of nanomaterials [1], lab-on-a-chip devices and biological analysis [2]. It offers many advantages over the conventional macroscopic devices because of its ... En savoir plus

Uniformity Correction for Fluid Coating Head

W. Vetterling
ZINK Imaging, Bedford, MA, USA

Slot coating is a widely used commercial process for applying one or more thin layers to a substrate such as paper, fabric, film or other material. In many cases, a highly uniform thickness is required, where a coating head that has been corrected for use with a Newtonian fluid may not ... En savoir plus

Drying of Corn Kernels: From Experimental Images to Multiscale Multiphysics Modeling

P. Takhar[1], and S. Zhang[2]

[1]Texas Tech University, Lubbock, Texas, USA
[2]Visualization Sciences Group Inc., Burlington Massachusetts, USA

This work demonstrated the importance and feasibility of experimental image to simulation workflow. The workflow is successfully applied to a food processing study, where multiphysics and multiscale modeling based on 3D experimental image reconstruction contributes to the preservation of ... En savoir plus

Simulation of the Dynamic Behavior of a Droplet on a Structured Surface using the Non-conservative Level Set Method

N. Boufercha, J. Sägebarth, and H. Sandmaier
Universität Stuttgart / IFF-MST, Stuttgart, Germany

The ongoing trend towards miniaturization, higher integration as well as cost efficiency will make it necessary to investigate a new assembly method for micro components. In this paper, a novel method of fluidic-based micro assembly is presented. A self-assembly effect which is caused by ... En savoir plus

Full-Wave Simulation of an Optofluidic Transmission-Mode Biosensor

E. P. Furlani[1], N. M. Litchinitse[2], and R. Biswas[2]

[1]The Institute for Lasers, Photonics and Biophotonics, University at Buffalo, Buffalo, New York, USA
[2]Department of Electrical Engineering, The State University of New York at Buffalo,Buffalo, New York, USA

We present a study of an optofluidic biosensor. The sensor operates in a transmission mode wherein detection is based on a shift in the transmission spectrum caused by the contrast in refractive index between the carrier fluid and the target biomaterial. We study the behavior of the ... En savoir plus

Numerical Optimization of Active Heat Sinks Considering Restrictions of Selective Laser Melting

F. Lange [1], C. Hein [1], C. Emmelmann [1],
[1] Fraunhofer Institution for Additive Production Technologies IAPT, Hamburg, Germany

Parametric and topology optimization approaches are widely used techniques for performance improvement of components in terms of various objectives. Especially topology optimization often leads to complex geometries that are difficult or impossible to produce by conventional ... En savoir plus

Model of a Filament Assisted CVD Reactor

J. Brcka[1]

[1]TEL US Holdings, Inc., Technology Development Center, Albany, New York, USA

In this presentation we are dealing with the computational fluid model of a Filament Assisted Chemical Vapor Deposition (FACVD) reactor. Proposed strategy in this study involved several steps: (a) development a computational model for FACVD process capable to describe and obtain with ... En savoir plus

Simulation of the Oxygen Supply of Osteoblastic Cells in Dynamic 3D Cell Cultures

P. Elter[1]
[1]University of Applied Sciences Mittelhessen, Germany

In biotechnology and medicine, cells are frequently grown on scaffolds with a three-dimensional channel structure. The oxygen and nutrient supply of the cells is realized by a medium flowing through the channels of the scaffolds. However, it is often difficult to obtain a confluent ... En savoir plus

Mathematical Investigation and CFD Simulation of Monolith Reactors: Catalytic Combustion of Methane

M. Ghadrdan[1], and H. Mehdizadeh[2]
[1]Department of Chemical Engineering, Norwegian University of Science and Technology (NTNU), Trondheim, Norway
[2]Department of Chemical Engineering, Tarbiat Modares University, Tehran, Iran

Interest in the production of hydrogen from hydrocarbons has grown significantly recently. In order to achieve high surface to volume ratio with reasonable pressure drop, monolithic reactors are used. The goal of this work is to develop a two-phase (gas & solid) transient catalytic ... En savoir plus

Premier

301–310 of 931

Dernier