Articles techniques et présentations

Recherche rapide

Ressources

White Papers and Application Notes

Ici vous trouverez les présentations issues des Conférences COMSOL à travers le monde. Réalisées par des utilisateurs de COMSOL Multiphysics, ces présentations explorent tous les domaines actuels d'innovation. Les applications couvrent pratiquement tous les secteurs industriels et impliquent des phénomènes électriques, mécaniques, fluidiques et chimiques. Utilisez la recherche rapide pour trouver les présentations les plus intéressantes dans votre domaine d'intérêt.

Consultez les proceedings de la Conference COMSOL 2020

All

Bengaluru 2023

Munich 2023

Inverse Analysis for Heat Transfer Coefficient Identification

F. Tondini[1], P. Bosetti[1], and S. Bruschi[1]

[1]DIMS, University of Trento, Trento, Italy

The hot stamping of boron steels for producing complex structural components of the car body-in-white is more and more widespread. Optimization of sheet forming technologies at elevated temperatures is still troublesome, since the thermal, mechanical and metallurgical phenomena ... En savoir plus

Oxidation of Metallic Nanoparticles

A. Auge[1], A. Weddemann[1], F. Wittbracht[1], B. Vogel[1], and A. Hütten[1]

[1]Department of Physics, Thin Films and Physics of Nanostructures, Bielefeld University, Bielefeld, Germany

The oxidation behavior of metallic nanoparticles is investigated in respect to material parameters like Mott potential, defects on the microstructure and oxide volume increase per ionic defect. An emphasis is laid on magnetic nanoparticles where the degree of oxidation can be measured ... En savoir plus

Simulation of Daisy Chain Flip-Chip Interconnections

G.S. Durante[1] and M. Fretz[1]

[1]CSEM Zentralschweiz, Alpnach Dorf, Switzerland

Flip-chip interconnection technologies have been tested through the use of a test chip with embedded single-bump daisy chains. The Flip-Chip technologies are selected among Au bump Thermocompression (TC) with and without Nonconductive Adhesives (NCA) underfiller, anisotropic conductive ... En savoir plus

Simulation of a Heated Tool System for Jet Electrochemical Machining

M. Hackert[1], G. Meichsner[2], and A. Schubert[1][2]

[1]Chair Micromanufacturing Technology, Faculty of Mechanical Engineering, Chemnitz University of Technology, Chemnitz, Germany
[2]Fraunhofer Institute for Machine Tools and Forming Technology, Chemnitz, Germany

Jet Electrochemical Machining (Jet-ECM) is an unconventional procedure using localized anodic dissolution for micromachining. An increasing of the electrolyte temperature will lead to an increase of the electrical conductivity of the electrolyte by about 30% and to a reduction of the ... En savoir plus

Modelling of Micro/Macro Densification Phenomena of Cu Powder during Capacitor Discharge Sintering

G. Maizza[1] and A. Tassinari[1]

[1]Dipartimento di Scienza dei Materiali ed Ingegneria Chimica, Politecnico di Torino, Torino, Italy

Capacitor Discharge Sintering (CDS) is an ultrafast Electric Current Assisted Sintering method (u-ECAS) suited for electrically conductive powders. It is characterized by relatively short processing times (milliseconds range) and much lower sintering temperatures than the melting point ... En savoir plus

Modelling of SiC Chemical Vapour Infiltration Process Assisted by Microwave Heating

G. Maizza[1] and M. Longhin[1]
[1]Dipartimento di Scienza dei Materiali ed Ingegneria Chimica, Politecnico di Torino, Torino, Italy

The excessive presence of residual SiC matrix inter-fiber pores is often the main cause for the very poor mechanical strength and toughness of SiC/SiC composites manufactured by CVI (Chemical Vapour Infiltration) process. This work presents a micro/macro Microwaveassisted Chemical Vapour ... En savoir plus

Dynamic Observation of Magnetic Particles in Continuous Flow Devices by Tunneling Magnetoresistance Sensors

A. Weddemann[1], A. Auge[1], F. Wittbracht[1], C. Albon[1], and A. Hütten[1]

[1]Department of Physics, Thin Films and Physics of Nanostructures, Bielefeld University, Bielefeld, Germany

Dynamic measurement of magnetic particles in continuous flow devices is made very difficult by the limitations imposed by the sensors themselves. Thus, certain sensor layouts are restricted to either number sensitive or spatial resolutive measurements of magnetic particles. We ... En savoir plus

Numerical Simulation of Pulsed TIG Welding Partial and Full Penetration

A. Traidia[1][2], F. Roger[1], and E. Guyot[2]

[1]Ecole Nationale Supérieure de Techniques Avancées, Palaiseau, France
[2]AREVA NP, Centre Technique Soudage, France

In this poster, a numerical model of spot pulsed current TIG welding for partially and fully penetrated weld pools is presented. Heat transfer and fluid flow in the weld pool driven by the combination of electromagnetic force, buoyancy force, surface tension gradient and latent heat are ... En savoir plus

A Study of Optical Sensor Based on Fiber Bragg Grating Using COMSOL Multiphysics^®

C. Gavrila[1] and I. Lancranjan[2]

[1]Technical University of Civil Engineering Bucharest, Bucharest, Romania
[2]Advanced Study Centre, National Institute for Aerospace Research “Elie Carafoli”, Bucharest, Romania

Fiber optic sensors can measure a large range of physical, chemical and environmental variables such as temperature, pressure, shape, position, chemical concentration, moisture, etc. Fiber optic sensors provide measurements in applications where the conventional electrical based sensors ... En savoir plus

Streamer Propagation in a Point-to-Plane Geometry

M. Quast[1] and N.R. Lalic[1]
[1]Gunytronic GmbH, St Valentin, Germany

Corona discharge is used in several applications such as surface treatment of polymers, photocopying or dust removal in air conditioning. Streamer formation is undesirable for most of these applications. Therefore, several studies have been dedicated to investigate the formation and ... En savoir plus

Premier

4721–4730 of 5677

Dernier