Articles techniques et présentations

Recherche rapide

Ressources

Livres Blancs

Voyez comment la modélisation et la simulation sont utilisées par les industries La modélisation et la simulation multiphysiques pilotent l'innovation dans tous les grands secteurs d'activité et dans le monde universitaire — comme en témoignent les nombreuses utilisations présentées dans des articles et des posters techniques présentés par des ingénieurs, chercheurs et scientifiques à la Conférence COMSOL chaque année. Inspirez-vous des récents proceedings réunis ci-dessous, ou, pour trouver les présentations les plus intéressantes dans votre domaine d'intérêt, utilisez la recherche rapide.

Consultez les proceedings de la Conference COMSOL 2024

Terme recherché:

Multiphysics Analysis of an Infrared Bolometer

J. S. Crompton [1], J. Thomas [1], K. Koppenhoefer [1],
[1] AltaSim Technologies, Columbus, OH, USA

Bolometers are used in a number of applications including night vision cameras, astronomy, and particle physics to measure the power of incident electromagnetic radiation. The general principle of operation is shown below: a strip of conducting material is exposed to incident ... En savoir plus

Towards the Modeling of Microgalvanic Corrosion in Aluminum Alloys: the Choice of Boundary Conditions

N. Murer[1], N. Missert[2], and R. Bucchheit[1]

[1]Fontana Corrosion Center, Ohio State University, Columbus, OH, USA
[2]Sandia National Laboratories, Albuquerque, NM, USA

Aluminum alloys in near-neutral, mildly aggressive solutions, undergo damage accumulation during corrosion, mostly due to the presence of micrometer-sized constituent intermetallic particles (IMP) that create a microstructural discontinuity at which localized corrosion occurs. The ... En savoir plus

A Heat Transfer Model for Ugitech’s Continuous Casting Machine

C. Deville-Cavellin
Dr.
Liquid Metal Metallurgy and Solidification department
Ugitech’s Research Center, Ugine, France

Dr. Christian Deville-Cavellin is a Research Engineer at Ugitech's Research Center, since 1995. Ugitech, member of the Schmoltz & Bickenbach group, is a stainless steel, long products producer. C. Deville-Cavellin is responsible for all research topics related to liquid metal ... En savoir plus

Micro cooling channel heat sinks designed by topology optimization

Hao Li [1], Xiaohong Ding [1], Dalei Jing [1], Min Xiong [1],
[1] University of Shanghai for science and technology

As a key component of MEMS, microprocessor with high computing performances is facing with severe thermal challenge due to the increasing power density, miniaturization as well as higher operating temperature requirements, and thermal management in corresponding fields has become one of ... En savoir plus

A MEMS Condenser Microphone for Consumer Applications

S. L. Pinjare, V. S. Nagaraj, S. N. Savitha, S. Kesari, M. S. Sagar, and K. R. Roshan
Nitte Meenakshi Institute of Technology

The MEMS microphone is also called microphone chip or silicon microphone. The pressure sensitive diaphragm is etched directly into a silicon chip by MEMS techniques and is usually accompanied with integrated preamplifier. Most MEMS microphones are variants of the condenser microphone ... En savoir plus

Model of Biosensor based on Organic Electrochemical Transistors

A. Shirinskaya [1], Y. Bonnassieux [1], G. Horowitz [1],
[1] LPICM, CNRS, Ecole Polytechnique, Université Paris Saclay, Palaiseau, France

One of the most promising categories of semiconductor-based sensors is organic electrochemical transistor (OECT), which consists of three electrodes (Source, Drain and Gate) and two active layers: electrolyte and conductive polymer. Despite the fact that OECT attracts a lot of attention ... En savoir plus

Design of a Self-Recharging Untethered Mobile Inspection Tool inside a Pipeline

W. Chalgham [1], A. C. Seibi [1],
[1] University of Louisiana at Lafayette, Lafayette, LA, USA

Pipeline inspection tools present some limitations related to power supply which require recharging after each operation. Using batteries or tethered tools make the duration to inspect any pipeline very limited and time consuming. This paper aims at designing a spherical self-recharging ... En savoir plus

Simulations of Polymer Based Micro Heater Operated at Low Voltage

M. Gayake[1], D. Bodas[2], and S. A. Gangal[1]
[1]Department of Electronic science, University of Pune, India
[2]Centre for Nanobioscience, Agharkar Research Institute, India

This paper presents a design of polymer based micro heater operating in the temperature range of 200- 250°C which could be operated at low voltage (battery operated). The micro heater has been designed and simulated using COMSOL 4.1, FEM simulation tool. Simulation was performed for ... En savoir plus

Simulation of a Polyimide Based Micromirror

A. Arevalo[1], S. Ilyas[2], D. Conchouso[1], I. G. Foulds[1,3]
[1]Computer, Electrical & Mathematical Sciences & Engineering Division (CEMSE), King Abdullah University of Science & Technology, Thuwal, Saudi Arabia
[2]Physical Sciences & Engineering (PSE), King Abdullah University of Science & Technology, Thuwal, Saudi Arabia
[3]School of Engineering, University of British Columbia - Okanagan, Vancouver, BC, Canada

The simulation of a micromirror using polyimide as the structural material is presented. The simulation was used to verify the initial design parameters and to explore the different characteristics of the electromechanical device. For simulation simplicity the electrodes are integrated ... En savoir plus

Extraction of 13.56 MHz NFC-Reader Antenna Parameters for Matching Circuit Design

Prof. Dr.-Ing. habil. A. K. Palit [1],
[1] ZF-Lemfoerder Electronic GmbH, ZF-Friedrichshafen AG. Group, Espelkamp, Germany

Introduction: RFID system uses a Transponder and the near field communication (NFC) antenna and a matching circuit (Figure-1) in which at least latter two must be optimally designed for a higher efficiency. Typically, RFID antennas are flat inductive coils with 2 to 4 turns and are ... En savoir plus

Premier

471–480 of 692

Dernier