Articles techniques et présentations

Recherche rapide

Ressources

Livres Blancs

Voyez comment la modélisation et la simulation sont utilisées par les industries La modélisation et la simulation multiphysiques pilotent l'innovation dans tous les grands secteurs d'activité et dans le monde universitaire — comme en témoignent les nombreuses utilisations présentées dans des articles et des posters techniques présentés par des ingénieurs, chercheurs et scientifiques à la Conférence COMSOL chaque année. Inspirez-vous des récents proceedings réunis ci-dessous, ou, pour trouver les présentations les plus intéressantes dans votre domaine d'intérêt, utilisez la recherche rapide.

Consultez les proceedings de la Conference COMSOL 2024

Terme recherché:

Metal Foam Tube Flow Characterisation

T. Spillmann[1]
[1]CSIRO, Energy Technology, Newcastle, New South Wales, Australia

In this study the flow through a tube filled with highly porous aluminium foam of three different pore sizes is analysed using COMSOL Multiphysics® CFD Module and compared to experimentally determined pressure drop data. Analyzing the flow through an array of pores allow the deduction of ... En savoir plus

Thermal Simulations of a LED Light Using COMSOL Multiphysics

M. Maaspuro[1]
[1]University of Turku, Turku, FInland

An experimental LED light composed of a multi-chip LED-module, a LED driver and an efficient heat sink, was investigated using COMSOL Multiphysics software and the Heat Transfer Module. In an LED light heat is mainly generated in the LEDs but some amount of heat is generated also in the ... En savoir plus

Numerical Modeling of the Near-Subsurface Temperature Distributions in the Presence of Time Varying Air Temperature in the Boundary Condition and Space Varying Temperature for the Initial Condition

M. Ravi[1], D. V. Ramana[1], R. N. Singh[1]
[1]CSIR - National Geophysical Research Institute, Hyderabad, Telangana, India

The subsurface thermal structure in presence of groundwater recharge/discharge has been obtained by applying the Robin type boundary condition at the earth’s surface. The Robin type boundary condition involves the effect air temperatures at the surface which are taken as exponentially ... En savoir plus

Modeling the Behavior of a Polymer Electrolyte Membrane within a Fuel Cell Using COMSOL

S. Beharry[1]
[1]University of the West Indies, St. Augustine, Trinidad and Tobago

One viable alternative to non-renewable fossil fuels is the fuel cell. A special class of FC i.e. Proton Exchange Membrane Fuel Cell (PEMFC) has been investigated during the present study. Membrane is a very important part of a PEMFC as most ohmic losses occurs here and limits the ... En savoir plus

How Finite Element Analysis Revolutionized a 100-Year Old Equation

K. Carlson [1], J. Arle [1], J. L. Shils [2], L. Mei [1],
[1] Beth Israel Deaconess Medical Center/Harvard Medical School, Boston, MA, USA
[2] Rush Medical Center, Chicago, IL, USA

In 1901 Weiss proposed an equation predicting activation of nerve fibers by electrical stimulation, used in neuroscience and neuromodulation, which applies electric fields to modify nerve behavior in neurological disorders. Weiss’ equation is relative to geometry, electrode array, ... En savoir plus

Some Clinical and Computational Studies On Haemodynamics In Stenosed Artery

A. Chanda, A.R. Choudhury, G. Ray, K. Dasgupta, and D. Nag
Jadavpur University, Kolkata, West Bengal, India

Atherosclerosis in arteries is caused by the formation of stenosis : fatty depositions, on the artery wall. In current medicine, the practice is to observe the maximum percentage occlusion at any arbitrary cross-section and diagnose the patient on that basis, which might not always ... En savoir plus

Key-Holes Magnetron Design and Multiphysics Simulation

A. Leggieri[1], F. Di Paolo[1], D. Passi[1]
[1]Univeristy of Rome "Tor Vergata" - Department of Electronic Engineering, Rome, Italy

This paper describes the design and characterization of an 8 slots resonant cavity Magnetron, which undergoes thermal-structural effects due to cathode heating. The proposed study involves Thermal Stress, Eigen-frequency and Particle Tracing analysis based on COMSOL Multiphysics®. ... En savoir plus

Modeling Microwave Heating During Batch Processing of a Liquid Sample in a Single Mode Cavity

S. Curet [1], F. Bellicanta Begnini [1], O. Rouaud [1], L. Boillereaux [1]
[1] L’UNAM Université, ONIRIS, CNRS, GEPEA, Nantes, France

The use of microwaves for heating purposes of dielectric materials is encountered in many industrial applications (food processing, chemistry, material engineering and medical applications). In most of these thermal applications, the prediction of the temperature evolution within the ... En savoir plus

Numerical Investigation of Strouhal Frequencies of Two Staggered Bluff Bodies

Eswaran M[1], P. Goyal[1], Anu Dutta[1], G.R. Reddy[1], R. K. Singh [1], K.K. Vaze[1]
[1]Bhabha Atomic Research Centre, Mumbai, India

A 2-D unsteady viscous flow around two cylinders is studied by numerical solutions of the unsteady Navier-Stokes equations with a finite element formulation using COMSOL Multiphysics®. The results of a numerical investigation of the Strouhal frequencies of two identical, stationary, ... En savoir plus

The Effects of the Electrical Double Layer on Giant Ionic Currents through Single Walled Carbon Nanotubes

G. Zhang[1][,][2][,][3], S.L. Bearden [1]
[1]Department of Bioengineering, Clemson University, Clemson, SC, USA
[2]Department of Electrical and Computer Engineering, Clemson University, Clemson, SC, USA
[3]Institute for Biological Interfaces of Engineering, Clemson University, Clemson, SC, USA

Electrofluidic transport through a single walled carbon nanotube (SWCNT) is enhanced by electroosmosis. Electroosmosis is made possible in these devices by the combination of a large slip length within SWCNTs and the interfacial potential at the solution/nanotube interface. A ... En savoir plus

Premier

631–640 of 931

Dernier