Note: This discussion is about an older version of the COMSOL Multiphysics® software. The information provided may be out of date.

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Moving Interior Wall in cdf

Please login with a confirmed email address before reporting spam

Hi,

I am studying pipe flow, currently in 2D.

I have placed a rigid interior wall, making a certain angle with the direction of flow, inside the pipe. Ideally, I would like it to rotate 'freely' around its first edge (see picture, the red point would be the axis). As of now, I am only using the Laminar Flow module.

By freely, I mean subjected to the flow. How can I achieve this?

1) the freely rotating axis
2) make the mesh follow the interior wall

I am reading this www.comsol.com/support/knowledgebase/970/ and looking for examples.

Thank you


4 Replies Last Post 15 mai 2012, 16:03 UTC−4
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 15 mai 2012, 13:38 UTC−4
Hi

I'm not sure COMSOL 4.2a allows you to simulate a thin wall like that (may be, perhaps someone else has managed) because for a FSi you need from, my knowledge, a domain (a surface in 2D). But you can make it thin and I would end it with two half circular ends to allow a better meshing and fluid separation (avoid right angle corners in CFD but also ACDC ...). Then to give a rotation axis, one way is to make a hollow cylinder and apply a roller structural BC or apply a weak equation to enforce a rotation

--
Good luck
Ivar
Hi I'm not sure COMSOL 4.2a allows you to simulate a thin wall like that (may be, perhaps someone else has managed) because for a FSi you need from, my knowledge, a domain (a surface in 2D). But you can make it thin and I would end it with two half circular ends to allow a better meshing and fluid separation (avoid right angle corners in CFD but also ACDC ...). Then to give a rotation axis, one way is to make a hollow cylinder and apply a roller structural BC or apply a weak equation to enforce a rotation -- Good luck Ivar

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 15 mai 2012, 15:53 UTC−4
Thank you for your reply

> But you can make it thin and I would end it with two half circular ends to allow a better meshing and fluid separation (avoid right angle corners in CFD but also ACDC ...)

Yes, maybe that will have to do (and thank you for the tips). I have used fillet (the circular ends, right?) and it bends the obstacle nicely. However, I want the obstacle to be rigid, so I guess I'd have to mess with the Young modulus. And add a constraint to a point?

I found this: www.comsol.com/community/forums/general/thread/15286/#p41764

Can someone point me in the right direction? My obstacle's movement will also come from an external ODE, I "just" don't know how to move the obstacle mid simulation.
Thank you for your reply > But you can make it thin and I would end it with two half circular ends to allow a better meshing and fluid separation (avoid right angle corners in CFD but also ACDC ...) Yes, maybe that will have to do (and thank you for the tips). I have used fillet (the circular ends, right?) and it bends the obstacle nicely. However, I want the obstacle to be rigid, so I guess I'd have to mess with the Young modulus. And add a constraint to a point? I found this: http://www.comsol.com/community/forums/general/thread/15286/#p41764 Can someone point me in the right direction? My obstacle's movement will also come from an external ODE, I "just" don't know how to move the obstacle mid simulation.

Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 15 mai 2012, 15:56 UTC−4
Hi
you could try with the Rigid Connector on your structural domain, that will enforce it to be "rigid"

--
Good luck
Ivar
Hi you could try with the Rigid Connector on your structural domain, that will enforce it to be "rigid" -- Good luck Ivar

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 15 mai 2012, 16:03 UTC−4
Again, thank you.

(had just found this www.comsol.dk/community/forums/general/thread/13559/#p36289)

Another day, another thing to explore in COMSOL...
Again, thank you. (had just found this http://www.comsol.dk/community/forums/general/thread/13559/#p36289) Another day, another thing to explore in COMSOL...

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.