Articles techniques et présentations

Recherche rapide

Ressources

Livres Blancs

Voyez comment la modélisation et la simulation sont utilisées par les industries La modélisation et la simulation multiphysiques pilotent l'innovation dans tous les grands secteurs d'activité et dans le monde universitaire — comme en témoignent les nombreuses utilisations présentées dans des articles et des posters techniques présentés par des ingénieurs, chercheurs et scientifiques à la Conférence COMSOL chaque année. Inspirez-vous des récents proceedings réunis ci-dessous, ou, pour trouver les présentations les plus intéressantes dans votre domaine d'intérêt, utilisez la recherche rapide.

Consultez les proceedings de la Conference COMSOL 2024

Terme recherché:

Computational Fluid Dynamics

The Use of CFD Simulations in Learning Fluid Mechanics at the Undergraduate Level

Marc K. Smith
Professor of Mechanical Engineering, Georgia Institute of Technology

Simple, accurate CFD simulations using COMSOL Multiphysics are used in a senior-level undergraduate course as a means to explore a number of fluid flows with the intent of developing a deep understanding of the underlying fluid mechanical mechanisms involved in the flows. Students also ... En savoir plus

Deep Desulfurization of Diesel Using a Single-Phase Micro-Reactor

G. Jovonavic[1], J. Jones[1], and A. Yokochi[1]
[1]School of Chemical, Biological and Environmental Engineering, Oregon State University, Corvallis, Oregon, USA

This paper describes the benefits of computational fluid dynamics in the development of a microreactor used in the desulfurization of aromatic compounds. It is crucial to verify diffusion and extinction coefficients to ensure accurate simulation results prior to experiments. COMSOL ... En savoir plus

Error Analysis in Estimating Temperature-Dependent Thermal Diffusivity and Kinetic Parameters using Heat Penetration Data

K.D. Dolan[1,2], A.R. Sommerlot[1], and D.K. Mishra[1]
[1]Department of Biosystems and Agricultural Engineering, Michigan State University, East Lansing, Michigan, USA
[2]Department of Food Science and Human Nutrition, Michigan State University, East Lansing, Michigan, USA

Growing consumer demand for nutraceuticals has stimulated interest by food companies to increase levels of these health-promoting compounds. Thermal processing of canned foods in a retort produces a unique problem: some of the nutraceuticals are highly sensitive to temperature, and ... En savoir plus

Model of a Filament Assisted CVD Reactor

J. Brcka[1]

[1]TEL US Holdings, Inc., Technology Development Center, Albany, New York, USA

In this presentation we are dealing with the computational fluid model of a Filament Assisted Chemical Vapor Deposition (FACVD) reactor. Proposed strategy in this study involved several steps: (a) development a computational model for FACVD process capable to describe and obtain with ... En savoir plus

Transient Simulation of a Naturally Ventilated Façade in a Mediterranean Climate

C. Balocco[1]
[1]Dipartimento di Energetica “Sergio Stecco”, Università degli Studi di Firenze, Firenze, Italy

Energy performances and building energy quality can be achieved by high performance envelopes. In this paper the thermal performance of a naturally ventilated façade, applied to a traditional wall, widely used in existing buildings, was investigated by a transient simulation. A ... En savoir plus

Helium Two-Phase Flow in a Thermosiphon Open Loop

B. Baudouy[1] and F. Visentin[1]
[1]CEA, Irfu, SACM, Gif-sur-Yvette, France

The construction of high magnetic field superconducting coils requires the use of low temperature superconductors that must be cooled down to liquid helium temperature (4.2 K). Natural two-phase convection loops, i.e. thermosiphon loop, are used as cooling system for large ... En savoir plus

An Analysis of Skimboard Hydrodynamics

N.D. Barnett[1], and E. Gutirrez-Miravete[2]
[1]General Dynamics-Electric Boat, Kingston, Rhode Island, USA
[2]Rensselaer at Hartford, Hartford, Connecticut, USA

This paper report on a study of the hydrodynamics of skimboards and surfboards using the computational fluid dynamics (CFD) module in COMSOL. The study analyzes the flow in a thin water layer underneath a skim board in a 2-D Cartesian coordinate. Three different sets of boundary ... En savoir plus

Helical Coil Flow: A Case Study

M. Cozzini[1]

[1]Renewable Energies and Environmental Technologies Research Unit, Fondazione Bruno Kessler, Povo, TN, Italy

Stationary flow configurations in curved pipes constitute an important subject from both the theoretical and the practical point of view. A typical application concerns the calculation of secondary flow effects on the thermal efficiency of heat exchangers. Motivated by a similar problem, ... En savoir plus

Modeling Contact Line Dynamics in Evaporating Menisci

J. Plawsky[1], A. Chatterjee[1], and P.C. Wayner Jr.[1]
[1]Department of Chemical and Biological Engineering, Rensselaer Polytechnic Institute, Troy, New York, USA

The Constrained Vapor Bubble is a fundamental fluid mechanics experiment that is scheduled to run aboard the International Space Station starting in August 2009. The experiment is focused on looking at evaporation and condensation processes at the contact line, where vapor, liquid and ... En savoir plus

An Analysis of Heat Conduction with Change of Phase with Application to the Solidification of Copper

J. Michalski[1], and E. Gutirrez-Miravete[2]
[1]Hamilton-Sundstrand
[2]Rensselaer at Hartford, Hartford, Connecticut, US

The goal of this study was to determine the possibility of using the finite element in COMSOL Multiphysics program to obtain a high accuracy solution to a moving boundary problem, specifically, the solidification of copper. A one-dimensional geometry in Cartesian coordinates was used to ... En savoir plus

Premier

871–880 of 1091

Dernier