Articles techniques et présentations

Recherche rapide

Ressources

Livres Blancs

Voyez comment la modélisation et la simulation sont utilisées par les industries La modélisation et la simulation multiphysiques pilotent l'innovation dans tous les grands secteurs d'activité et dans le monde universitaire — comme en témoignent les nombreuses utilisations présentées dans des articles et des posters techniques présentés par des ingénieurs, chercheurs et scientifiques à la Conférence COMSOL chaque année. Inspirez-vous des récents proceedings réunis ci-dessous, ou, pour trouver les présentations les plus intéressantes dans votre domaine d'intérêt, utilisez la recherche rapide.

Consultez les proceedings de la Conference COMSOL 2024

Terme recherché:

Simulation of the Dynamic Behavior of a Droplet on a Structured Surface using the Non-conservative Level Set Method

N. Boufercha, J. Sägebarth, and H. Sandmaier
Universität Stuttgart / IFF-MST, Stuttgart, Germany

The ongoing trend towards miniaturization, higher integration as well as cost efficiency will make it necessary to investigate a new assembly method for micro components. In this paper, a novel method of fluidic-based micro assembly is presented. A self-assembly effect which is caused by ... En savoir plus

Effect of Substrate Contact Angle on Ink Transfer in Flexographic Printing

F. E. Hizir[1], D. E. Hardt[1]
[1]Massachusetts Institute of Technology, Cambridge, MA, USA

Flexography is a roll-based mass printing process used in manufacture of printed products such as sensors, self-cleaning surfaces, and flexible electronics. Flexography involves inking of a stamp wrapped around a roller, and the transfer of ink on the stamp surface to a printing ... En savoir plus

Deformation of Stamp Features with Slanted Walls During Microcontact Printing

F. E. Hizir[1], H. M. Al-Qahtani[1, 2], D. E. Hardt[1]
[1]Massachusetts Institute of Technology, Cambridge, MA, USA
[2]King Fahd University of Petroleum and Minerals, Dhahran, Saudi Arabia

Microcontact printing is a method for depositing patterns of thin films or molecular monolayers on surfaces using a polydimethylsiloxane (PDMS) stamp for selective mechanical contact (Figure 1). Undesired deformation of the stamp features during printing affects printed pattern quality. ... En savoir plus

Optimization Module Enables Hybrid Experimental-Numerical Algorithm for 3D Particle Image Velocimetry

M. Sigurdson[1], C. Meinhart[1], I. Mezic[1]
[1]Department of Mechanical Engineering, University of California - Santa Barbara, Santa Barbara, CA, USA

In our study of chaotic mixing, 3D velocity measurements (u,v,w) are required for evaluation of a micro mixer using a mix-prediction algorithm. The hybrid approach presented here combines 2D measurements, an imperfect numerical model, and appropriate fitting parameters. Because our ... En savoir plus

Fast Biofluid Transport of High Conductive Liquids Using AC Electrothermal Phenomenon, A Study on Substrate Characteristics

A. Salari[1], C. Dalton[1]
[1]University of Calgary, Calgary, AB, Canada

AC electrothermal (ACET) micropumps are based on the temperature gradient caused by Joule heating or an external heat source in the bulk of an electrolyte. In this paper, a 2D simulation was performed to study the effect of substrate thickness and material (glass and silicon) for an ACET ... En savoir plus

Flow Focusing Droplet Generation Using Linear Vibration

A. Salari[1], C. Dalton[1]
[1]Department of Electrical & Computer Engineering, University of Calgary, Calgary, AB, Canada

Flow focusing microchannels are widely used in droplet generation mechanisms. In this paper, the effect of linear vibration on the flow pattern in a flow focusing structure and the corresponding formed droplets were numerically investigated using COMSOL Multiphysics® software. The ... En savoir plus

Structural Optimization of the AISHa Ion Source

F. Noto[1], M. Piscopo[1], L. Celona[1], D. Cittadino[1], S. Gammino[1], G. Cuttone[1], G. Gallo[1], G. Schillaci[1], C. Campisano[2], L. Lo Nigro[3], G. Costa[3], A. Campisano[4]
[1]Laboratorio Nazionale del Sud, Santa Sofia, Catania, Italy
[2]Gravina di Catania, Sicily, Italy
[3]Trinacria, Canalicchio, Catania, Italy
[4]Unico Informatica, li Battiati, Catania, Italy

Different facilities for hadrontherapy have been built in the recent past. AISHa ion source has been designed by keeping in mind the typical requirements of hospital-based facilities, where the minimization of the mean time between failures (MTBF) is a key point together with the ... En savoir plus

Numerical Investigation of Micronozzle Performance for Various Nozzle Geometries

P. A. Haris[1], T. Ramesh[1]
[1]National Institute of Technology Tiruchirappalli, Tiruchirappalli, Tamil Nadu, India

Design and manufacture of thrusters for producing very low thrust force in the range of milli or micro newtons using micronozzles has been actively developed in the last decade. The nature of propellant flow in such micronozzles differs from that of macro nozzles. In micronozzles, ... En savoir plus

Effect of Magnetic Field on MR-Fluid in Ball End Magnetorheological Finishing

H. Garg[1], V. S. Negi[1], A. S. Kharola[1], R. Sharma[1]
[1]CSIR - Central Scientific Instruments Organization, Chandigarh, India

Magnetorheological Finishing (MRF) is one of the precision finishing processes in which magnetic field is used to drive abrading forces for Finishing 2D and complex 3D surfaces. In this paper, Ball End Magnetorheological Finishing (BEMRF) has been analyzed for fluid behaviors under the ... En savoir plus

Hydrodynamic Flow Focusing for Microfluidic Cell Sorting Chip

N. Mehendale[1], D. Paul[1]
[1]Indian Institute of Technology Bombay, Mumbai, Maharashtra, India

Hydrodynamic flow focusing is an important requirement of microfluidic cell sorting devices. It allows the cells to arrive sequentially at the sorting location making detection easier. The simplest flow focusing configuration uses a three input Y-shaped microchannel. The sample enters ... En savoir plus

Premier

291–300 of 336

Dernier