Articles techniques et présentations

Recherche rapide

Ressources

Livres Blancs

Voyez comment la modélisation et la simulation sont utilisées par les industries La modélisation et la simulation multiphysiques pilotent l'innovation dans tous les grands secteurs d'activité et dans le monde universitaire — comme en témoignent les nombreuses utilisations présentées dans des articles et des posters techniques présentés par des ingénieurs, chercheurs et scientifiques à la Conférence COMSOL chaque année. Inspirez-vous des récents proceedings réunis ci-dessous, ou, pour trouver les présentations les plus intéressantes dans votre domaine d'intérêt, utilisez la recherche rapide.

Consultez les proceedings de la Conference COMSOL 2024

Toutes

Boston 2025

Terme recherché:

building

Vibro-acoustic modeling, analysis and optimization using COMSOL Multiphysics

Yu Xiang [1],
[1] Agency for Science, Technology and Research (Institute of High Performance Computing), Singapore

Vibro-acoustics encompasses the study of interaction between sound and vibration. For example, sound transmission analysis is important to design vehicle bodies and building partitions, advanced noise control technologies can ease the increasing noise pollution problem in densely ... En savoir plus

Assessing the Potential of Ventilated Facades on Reducing a Buildings’ Thermal Load Using Decoupled COMSOL Simulations

J. van Schijndel[1], C. van Dronkelaar[1]
[1]Eindhoven University of Technology, Eindhoven, The Netherlands

Solar radiation is a prominent contributor of energy in buildings, and can be transmitted directly into a building through opaque surfaces, but it can also be absorbed by building components (i.e. walls, roofs etc.). This study discusses the use and effect of ventilated facades, with an ... En savoir plus

Surface to Surface Radiation Benchmarks

J. v. Schijndel [1], R. v. Eck [1], M. Klep [1],
[1] Eindhoven University of Technology, Eindhoven, Netherlands

The paper presents a student guide on how to implement surface to surface radiation within COMSOL Multiphysics® software for case studies found within the built environment. We included four benchmarks: (1) Radiation in a triangular cavity with infinite length; (2) Radiation between two ... En savoir plus

Modeling an electric cell actuator and loudspeaker using COMSOL Multiphysics

W. J. Wu
NTU Nano-Bio MEMS Group
National Taiwan University,
Taiwan

This presentation presented the following: * The building of an FEA model of an electric cell actuator using COMSOL Multiphysics * Validation of this model through the AVID and ESPI measurement systems * The building of an FEA model of an electric loudspeaker using COMSOL Multiphysics * ... En savoir plus

Modelling and Experimental Validation Possibilities of Heat Transfer Room Model

M. Zalesak, and V. Gerlich
Tomas Bata University in Zlin, Zlin, Czech Republic

The study presents first authors experience with COMSOL Multiphysics environment used as a possible modeling tool of thermal building behavior. The idea of the project was to gain thermal response to changed boundary conditions with the application of COMSOL environment as a modeling ... En savoir plus

PIR Sensor Modeling and Simulation Using COMSOL Multiphysics® and its Ray Optics Module

M. Maaspuro [1],
[1] School of Electrical Engineering, Aalto University, Finland

PIR (Passive Infrared) sensor is the most widely used motion sensor for occupancy detection in building automation applications. Normally, only the binary information indicating presence or absence is used. However, an advanced analysis of the PIR sensor analog signal can results in more ... En savoir plus

Influence of a Refurbishing on an Old Residential Building’s Wall in Paris in Summer: Mass and Heat Transfer Approach

K. Azos-Diaz[1], B. Tremeac[2], F. Simon[2], D. Corgier[2], C. Marvillet[1]
[1]Laboratoire de Chimie Moléculaire, Génie des Procédés Chimique et Energétique, Paris, France
[2]MANASLU Ing., Savoie Technolac, Le Bourget du Lac, France

The implementation of thermal insulation in old residential building walls could compromise the hygrothermal behavior of the construction, especially in summer time when it is placed inside. A bad installation of insulation could have consequences on the quality of indoor air conditions ... En savoir plus

The APP as a Tool, A First Principles Approach

R. W. Pryor[1],
[1] Pryor Knowledge Systems, Inc., Bloomfield Hills, MI, USA

The app discussed in this paper is based on a COMSOL Multiphysics® 1D heat transfer model that analyses the heat flow through a double pane window, with a gas chamber between the two panes, as would normally be mounted in the wall of a building, a container or a refrigerated chamber. The ... En savoir plus

Assessing the risk of cracking for wooden sculptures due to dynamic relative humidity changes

M. Sobon¹, L. Bratasz¹
¹Jerzy Haber Institute of Catalysis and Surface Chemistry, Poland

Wooden sculptures are an important part of European cultural heritage, but they are also among the most vulnerable objects to variations of temperature and relative humidity (RH). Fluctuations in the ambient environment can lead to irreversible structural and aesthetical damage. The ... En savoir plus

Simulation of Electro-Thermal Transients in Superconducting Accelerator Magnets

L. Bortot [1], M. Maciejewski [2], M. Prioli [1], B. Auchmann [3],
[1] CERN, Geneva, Switzerland
[2] CERN, Geneva, Switzerland; Lodz University of Technology, Lodz, Poland
[3] CERN, Geneva, Switzerland; Paul Scherrer Institute, Zurich, Switzerland

The paper presents the application of COMSOL Multiphysics® software to the modelling of superconducting accelerator magnets. A 2D magneto-thermal model is developed, using an equivalent magnetization formulation to take into account the eddy-currents’ effects. Due to the model ... En savoir plus

Premier

91–100 of 623

Dernier