Articles techniques et présentations

Recherche rapide

Ressources

Livres Blancs

Voyez comment la modélisation et la simulation sont utilisées par les industries La modélisation et la simulation multiphysiques pilotent l'innovation dans tous les grands secteurs d'activité et dans le monde universitaire — comme en témoignent les nombreuses utilisations présentées dans des articles et des posters techniques présentés par des ingénieurs, chercheurs et scientifiques à la Conférence COMSOL chaque année. Inspirez-vous des récents proceedings réunis ci-dessous, ou, pour trouver les présentations les plus intéressantes dans votre domaine d'intérêt, utilisez la recherche rapide.

Consultez les proceedings de la Conference COMSOL 2024

Toutes

Boston 2025

Terme recherché:

"transducer"

Acoustics - Structure Interaction Studies of Fiber Optic Mandrel Hydrophne using COMSOL Multiphysics®

Ashida Pradeep [2], Sreehari C.V. [1], Lav Kumar [1], R Rajesh [1], Vivek K [1], K P B Moosad [1]
[1] Naval Physical and Oceanographic Laboratory, Kochi, Kerala, India
[2] Govt. Model Engineering College, Kochi, Kerala, India

Hydrophones are acoustic receivers, which can be used to listen to the sound propagating underwater for the purposes of monitoring marine life, or other sound producing activities in the sea. Commonly used hydrophones are based on piezoelectric transducers. With the introduction of fiber ... En savoir plus

Thermal Analysis of a Piezo-Disk Ultrasound Probe

L. Spicci[1], M. Cati[1]
[1]Esaote, Firenze, Italy

Ultrasound imaging probes are widely used for several types of diagnosis applications. In the present work we focus our attention on a disk-type probe, which is widely used in CW and PW operating conditions. In particular we present a 2D-axial symmetry FEM for the probe, capable to ... En savoir plus

Heat Generation from Dielectric Loss, Internal Heat Generation and Vibration in COMSOL4.2 Multiphysics

T. R. Jeba, B. Vins, and V. Ramamoorthy
HCL Technologies

This paper presents a FEA approach to estimate temperature rise and thermal stress experienced in PZT/Solid structure due to internal heat generation and dynamic excitation. The power dissipative density consumed by structural damping of the mass structure, internal heat generation due ... En savoir plus

Optimization of Bending-Type Ultrasonic Transducers with Rotational Symmetry Using COMSOL Multiphysics^®

M. Jungwirth[1] and M. Rabl[1]

[1]Wels School of Engineering, Upper Austria University of Applied Sciences, Wels, Austria

Ultrasonic sensors are commonly used for a wide variety of non-contact presence, proximity or distance measuring applications in industry, especially the automotive branch. This paper shows how the radiation properties of bending-type ultrasonic transducers with rotational symmetry ... En savoir plus

FEM Simulation for ‘Pulse-Echo’ Performances of an Ultrasound Imaging Linear Probe

L. Spicci[1]
[1]Esaote SpA, Florence, Italy

Pulse-echo FEM simulation is seldom found in literature for ultrasound imaging array probes, since the complete modeling of such device is extremely complicated. Nevertheless, the 2D FEM described in the present work was successful, thanks to the following design procedure (see figure): ... En savoir plus

Calibration of Ultrasonic Testing for Faults Detection in Stone Masonry

M. Usai[1], S. Carcangiu[1], G. Concu[2]
[1]Department of Electrical and Electronic Engineering, University of Cagliari, Cagliari, Italy
[2]Department of Civil Engineering, Environmental and Architecture, University of Cagliari, Cagliari, Italy

In the field of assessment methodologies, particular importance is given to Non-Destructive Testing Techniques, which aspire to achieve the highest number of information about materials and structures without altering their condition. Ultrasonic Testing exploits the transmission and ... En savoir plus

Acoustic Streaming Driven Mixing

N. Nama [1], P. Huang [1], F. Costanzo [1], T. J. Huang [1]
[1] Department of Engineering Science and Mechanics, Pennsylvania State University, PA, USA

Introduction - The ability to achieve rapid and homogeneous mixing at microscales is one of the essential requirements for various lab-on-a-chip applications [1]. The flow at microscales is characterized by low Reynolds number, resulting in laminar flow patterns. Thus, the mixing at ... En savoir plus

Simulation of Impact Damage in a Composite Plate and Its Detection

V. Pavelko[1], I. Pavelko[1], M. Smolyaninovs[1], H. Pffeifer[2], M. Wevers[2]
[1]Riga Technical University, Riga, Latvia
[2]Catholic University Leuven, Leuven, Belgium

A problem of damage prediction in aircraft structure and its non-destructive evaluation is very important for aircraft structural health assessment. The analysis of the features of direct impact of thin-walled laminate component of aircraft was performed by COMSOL Multiphysics software. ... En savoir plus

Load Cell Design Using COMSOL Multiphysics

A. Marchidan[1], T. Sullivan[1], J. Palladino[1]
[1]Trinity College, Hartford, CT, USA

COMSOL Multiphysics was used to design a binocular load cell. A three-dimensional linear solid model of the load cell spring element was studied to quantify the high-strain regions under loading conditions. The load cell was fabricated from 6061 aluminum, and general purpose Constantin ... En savoir plus

Piezoelectric Transducers and Ultrasound Imaging: Impact of Materials Properties and Multiphysics Aided Design

Marco Cati graduated cum laude and encomium citation in electronic engineering in 2001 from the University of Florence, where in 2005 he also received a Ph. D. degree in electronic engineering. In 2005 he joined the Research & Development Department of Esaote where he is currently in ... En savoir plus

Premier

161–170 of 248

Dernier