Articles techniques et présentations

Recherche rapide

Ressources

Livres Blancs

Voyez comment la modélisation et la simulation sont utilisées par les industries La modélisation et la simulation multiphysiques pilotent l'innovation dans tous les grands secteurs d'activité et dans le monde universitaire — comme en témoignent les nombreuses utilisations présentées dans des articles et des posters techniques présentés par des ingénieurs, chercheurs et scientifiques à la Conférence COMSOL chaque année. Inspirez-vous des récents proceedings réunis ci-dessous, ou, pour trouver les présentations les plus intéressantes dans votre domaine d'intérêt, utilisez la recherche rapide.

Consultez les proceedings de la Conference COMSOL 2024

Terme recherché:

Simple Finite Element Model of the Topografiner

H. Cabrera[1], D. A. Zanin[1], L. G. De Pietro[1], A. Vindigni[1], U. Ramsperger[1], D. Pescia[1]
[1]Laboratory for Solid State Physics, ETH Zürich, Zürich, Switzerland

In our recent experiments we are revisiting the topografiner technology for the imaging of surface topography with a resolution of a few nanometers. In these new technique called Near-Field Emission Scanning Electron Microscopy (NFESEM), low-energy electrons are emitted from a ... En savoir plus

Design and Simulation of a MEMS-Based Ultrasonic Transducer for Viscosity Sensing Applications

Rahul Goyal [1], Divya Mohan Yadav [1],
[1] Indian Institute of Science, Bangalore, Karnataka, India

Technologies based on micro electro mechanical systems (MEMS) present advantages for rheological applications as they enable the fabrication of smaller sensors with faster response times. In this work we propose fabrication parameters and simulation of a MEMS viscometer. This research ... En savoir plus

Study of Pull-In Voltage in MEMS Actuators

P. D. Hanasi[1], B. G. Sheeparamatti[1], B. B. Kirankumar[1]
[1]Basaveshwar Engineering College, Bagalkot, Karnataka, India

Micro cantilevers are the basic MEMS structures, which can be used both as sensors and actuators. The . The objective of this work is to study concept of pull-in voltage and how to reduce the same. Voltage is applied to upper cantilever beam and lower contact electrode is made as ground. ... En savoir plus

Development of a Micro Ultrasonic Transducer

F. F. Dall'Agnol[1], A. C. F. de Mattos[1]
[1]Center for Information Technology Renato Archer (CTI), Campinas, SP, Brazil

We simulate a Capacitive Micromachined Ultrasound Transducer (CMUT) using COMSOL Multiphysics® software. The CMUT is an electromechanical system, therefore, we couple the physics of electrical and structural mechanics to describe its dynamics. We obtain the distributions of the electric ... En savoir plus

Modeling Implementation of Smart Materials such as Shape Memory Alloys and Electro-Active Metamaterials

Manuel Collet
PhD
Femto-STInstitute UMR CNRS 6174 Dept Applied Mechanics,
Besancon, France

Manuel Collet is a member of the Department of Applied Mechanics of the FEMTO-ST Institute. He graduated with a degree in Mechanical Engineering from Ecole Centrale de Lyon in 1992 and obtained his PhD in 1996 about Active control of vibrating structures by mean of semi distributed ... En savoir plus

Design and Analysis of a Three-DOF Piezoelectric Vibration Energy Harvester

R. T. P. Reddy [1], X. Xiong [2], J. Hu [3],
[1] University of Bridgeport, Bridgeport, CT, USA
[2] Department of Electrical and Computer Engineering, University of Bridgeport, Bridgeport, CT, USA
[3] Department of Mechanical Engineering, University of Bridgeport, Bridgeport, CT, USA

Introduction: Vibration energy harvester can convert mechanical vibration energy into electrical energy and store it in battery for later use. It can create clean renewable energy from vibration movements such as walking, jumping, running, etc. This can convert energy previously wasted ... En savoir plus

Electric Field Assisted Formation of Polymeric Hollow Microstructures

Vivek [1], S. Baranwal [1], A. Bindal [1], R. Mukherjee [1], A. Atta [1]
[1]IIT Kharagpur, West Bengal, India

Hollow microstructures find numerous applications in microsystems, bioMEMS and microfluidic systems [1]. Consequently, one-step fabrication process of hollow polymeric microstructures by external electric field along with capillary forces, termed as electric field- assisted capillarity ... En savoir plus

Sensibility Analysis of Inductance Involving an E-core Magnetic Circuit for Non Homogeneous Material

K. Z. Gomes [1], T. A. G. Tolosa [1], E. V. S. Pouzada [1],
[1] Mauá Institute of Technology, São Caetano do Sul, SP, Brazil

In this work, a methodology is developed, based on the application of finite element method in the frequency domain, using the COMSOL Multiphyics software, aiming the sensibility analysis of inductance calculation involving some configurations of an E-core magnetic circuit. Such ... En savoir plus

Magneto-hydrodynamic Flow in Electrolyte Solutions

M. Qin[1], and H. Bau[1]
[1]Department of Mechanical Engineering and Applied Mechanics, University of Pennsylvania, Pennsylvania, USA

The paper presents and compares two models for simulating magneto-hydrodynamic flow of RedOx electrolyte in a conduit patterned with circular pillars. The first model solves the coupled Nernst-Planck and Navier-Stokes equations subjected to Butler-Volmer electrode kinetics and provides ... En savoir plus

Meshing Challenges in Simulating the Induced Currents in Vacuum Phototriode

S. Zahid [1], P. R. Hobson [1],
[1] Brunel University London, London, United Kingdom

Vacuum phototriodes (VPT) have been used as photodetectors for many years in particle physics experiments. For example, they were used in the OPAL experiment at LEP and are currently used in the endcap Electromagnetic Calorimeter of the CMS experiment, at CERN’s Large Hadron Collider. ... En savoir plus

Premier

261–270 of 483

Dernier