Articles techniques et présentations

Recherche rapide

Ressources

Livres Blancs

Voyez comment la modélisation et la simulation sont utilisées par les industries La modélisation et la simulation multiphysiques pilotent l'innovation dans tous les grands secteurs d'activité et dans le monde universitaire — comme en témoignent les nombreuses utilisations présentées dans des articles et des posters techniques présentés par des ingénieurs, chercheurs et scientifiques à la Conférence COMSOL chaque année. Inspirez-vous des récents proceedings réunis ci-dessous, ou, pour trouver les présentations les plus intéressantes dans votre domaine d'intérêt, utilisez la recherche rapide.

Consultez les proceedings de la Conference COMSOL 2024

Terme recherché:

Microfluidic Simulation of a Separation System of T.cruzi from Blood Samples

S. L. Florez [1], M. J. Noguera [1], A. L. Campaña [1], J. C. Cruz [1], J. F. Osma [2],
[1] Department of Biomedical Engineering, University of Los Andes, Bogotá, Colombia
[2] Department of Electrical and Electronics Engineering, Microelectronics Center, University of Los Andes, Bogotá, Colombia

In 2014, it was estimated that there are between 6 to 7 million people worldwide infected by Chagas disease and approximately 25 million people are currently at risk. The parasite Trypanosoma cruzi (T. cruzi) causes this disease and according to the World Health Organization (WHO) it can ... En savoir plus

Effects of Thermal and Electro-Osmotic Flux on Grounding Electrodes

I. Ferreira de Rezende Costa¹, M. C. Barbosa¹, A. De Oliveira Costa Neto²
¹UFRJ, Rio de Janeiro, RJ, Brazil
²UFVJM, Teófilo Otoni, MG, Brazil

Electricity has become the main source of heat, power, and light used in the modern world. Much of the technological advances made over the last few decades are due to electrical energy. One of the essential components of the electrical system is the grounding network. The continuous ... En savoir plus

Simulation of Mass Transfer in a Microfluidic Experiment Using the Moving Mesh Method

K. Weisbrod[1], R. Roberts[1], R. Chamberlin[1], S. Yarbro[1]
[1]Los Alamos National Lab, Los Alamos, NM, USA

Multiphase flow in a microreactor was studied numerically for two immiscible liquids. Validation of the model was sought by simulating the flow behavior and mass transfer characteristics of a neutralization reaction described in the literature. Contact angles, interfacial tension and the ... En savoir plus

PCCP Profiling and Tube Wave Analysis of WRE Signal

N. Chowdhury[1], Z. Liao[2], and L. Zhao[1]
[1]Department of Electrical & Computer Engineering, Ryerson University, Toronto, ON, Canada
[2]Department of Architectural Science, Ryerson University, Toronto, ON, Canada

Acoustic wave propagation due to the breakage or slippage of reinforced wire in water-filled prestressed concrete cylinder pipe (PCCP) attracts interest in non-destructive pipe testing. Current practice of acoustic emission (AE) detection and wire-break related events (WRE) recognition ... En savoir plus

Using COMSOL® for the Development of the UK’s Second Hyperloop Prototype

A. Jocas [1], I. C. H, Chan [1], A. Malekos [1], H. P. Chan [1],
[1] The University of Edinburgh, UK

Hyperloop is a future concept of mass transportation proposed by Elon Musk. It uses electromagnetic propulsion to accelerate a passenger or cargo pod through a low-pressure tube. HYPED, the University of Edinburgh’s Hyperloop Team has created a prototype that uses linear halbach arrays ... En savoir plus

Modeling of Substrate Plate Preheating to Predict Efficiency in the Electron Beam Melting Process

M.Michatz [1], S. Janson [2], G. Schlick [3], I. Kühne [4], A. Frey [5],
[1] University of Applied Science, Faculty of Mechanical Engineering, Augsburg, Germany; Fraunhofer Research Institution for Casting, Composite and Processing Technology IGCV, Augsburg, Germany
[2] iwb Application Center Augsburg part of the Technical University of Munich (TUM), Augsburg, Germany
[3] Fraunhofer Research Institution for Casting, Composite and Processing Technology IGCV, Augsburg, Germany
[4] Heilbronn University, Faculty of Technology and Economics, Künzelsau, Germany
[5] University of Applied Science, Faculty of Electrical Engineering, Augsburg, Germany

Additive Manufacturing is revolutionizing the industrial sector for complex and individualized metallic components. The most limiting factor of the widely established laser beam melting technology is the scan velocity due to inertia of the mirrors [1]. In electron beam melting (EBM), ... En savoir plus

Modeling Approach to Facilitate Thermal Energy Management with Phase Change Materials (PCM)

D. Rubinetti [1], D. A. Weiss [1], A. Chaudhuri [2], D. Kraniotis [2],
[1] Institute of Thermal and Fluid-Engineering, University of Applied Sciences and Arts Northwestern Switzerland
[2] Department of Civil Engineering and Energy Technology, Oslo Metropolitan University, Norway

Thermal energy storage systems receive notable attention within the framework of energy management due to their ability of bridging thermal energy demand and supply, thus leading to an overall efficiency increase. The key component in such systems are materials which convert ... En savoir plus

The Effect of Microchannel Geometry on Dispersing Solute Asymmetries

A. Taylor [1], D. Harris [1],
[1] Brown University, Providence, RI, USA

Within the field of microfluidics, scientists and engineers have found ways to manipulate flow at the micron scale in order to downsize standard experimental procedures. These techniques boast faster results while consuming less resources. Microfluidic devices can be used for point-of ... En savoir plus

Linear Water Wave Propagation around Structures

L. Martinelli, and A. Lamberti
Universita di Bologna, Italy

Objective of this contribution is to show how to implement the Mild Slope Equations with COMSOL Multiphysics. These equations are commonly used to study the propagation of waves in harbors. Some interesting features are presented, namely the use of weak terms (used for the modelling of ... En savoir plus

Thermohydraulic Study of a Fixed Bed for the Core of a Nuclear Reactor

J. C. Almachi [1], J. A. Montenegro [1],
[1] Departamento de Formación Básica, Escuela Politécnica Nacional, Quito, Pichincha, Ecuador

The fixed beds have the advantage of large heat transfer area, for they are used in some designs of innovative nuclear reactors as the reactor FBNR. Inside of study of fixed beds is important to define the following parameters: flow minimum and velocity profile of cooling fluid, ... En savoir plus

Premier

331–340 of 1392

Dernier