Articles techniques et présentations

Recherche rapide

Ressources

Livres Blancs

Voyez comment la modélisation et la simulation sont utilisées par les industries La modélisation et la simulation multiphysiques pilotent l'innovation dans tous les grands secteurs d'activité et dans le monde universitaire — comme en témoignent les nombreuses utilisations présentées dans des articles et des posters techniques présentés par des ingénieurs, chercheurs et scientifiques à la Conférence COMSOL chaque année. Inspirez-vous des récents proceedings réunis ci-dessous, ou, pour trouver les présentations les plus intéressantes dans votre domaine d'intérêt, utilisez la recherche rapide.

Consultez les proceedings de la Conference COMSOL 2024

Toutes

Boston 2025

Terme recherché:

"solid mechanics"

Simulation of Acoustic Energy Harvesting Using Piezoelectric Plates in a Quarter-Wavelength Straight-Tube Resonator

B. Li[1], J.H. You[1]
[1]Southern Methodist University, Dallas, TX, USA

An acoustic energy harvesting mechanism at low frequency (~200 Hz) using lead zirconate titanate (PZT) piezoelectric cantilever plates placed inside a quarter-wavelength straight-tube resonator has been studied using COMSOL Multiphysics 4.3 and compared with experimental data. When the ... En savoir plus

Finite Element Solution of Nonlinear Transient Rock Damage with Application in Geomechanics of Oil and Gas Reservoirs

S. Enayatpour[1], T. Patzek[1]
[1]The University of Texas at Austin, Austin, TX, USA

The increasing energy demand calls for advances in technology which translate into more accurate and complex simulations of physical problems. Understanding the rock damage is essential to understanding the geomechanics of hydrocarbon reservoirs. The fragile microstructure of some ... En savoir plus

Sliding Performance of a Hyperelastic Seal

H. van Halewijn[1]
[1]Physixfactor, Nijmegen, The Netherlands.

A hyperelastic seal is pulled over a metal ring in a coffee machine for maintenance reasons. The force needed to pull the hyper elastic seal over the part is too high and should be reduced for maintenance reasons. Using the COMSOL Multiphysics® Structural Mechanics Module, and using the ... En savoir plus

Simulation of Wear using LiveLink™ for MATLAB®

D. Sutton[1]
[1]National Centre for Advanced Tribology at Southampton, University of Southampton, Southampton, United Kingdom

An incremental wear model has been developed using COMSOL Multiphysics® with MATLAB® to predict the evolution of component geometry as a result of wear. Whilst Archard’s wear law is a well-known empirical model for the prediction of wear volume, the design engineer is interested in ... En savoir plus

Residual Stresses and Failure Probability of Solid Oxide Fuel Cells Due to the Sintering Process

F. Greco[1], J. van Herle[1], A. Nakajo[1]
[1]FUELMAT Group, Institute of Mechanical Engineering, Ecole Polytechnique Fédérale de Lausanne, Lausanne, Switzerland

A solid oxide fuel cell (SOFC) is composed of four layers (anode, electrolyte compatibility layer and cathode) of different ceramic materials. The anode layer is produced by tape casting, the remaining layers are deposited by screen-printing. The layers are sintered together at high ... En savoir plus

Modeling Flow and Deformation During Salt-Assisted Puffing of Single Rice Kernels

T. Gulati[1], A. K. Datta[1]
[1]Department of Biological & Environmental Engineering, Cornell University, Ithaca, NY, USA

Puffing of biomaterials involves mass, momentum and energy transport along with large volumetric expansion of the material. Development of physics-based models that can describe heat and moisture transport, rapid evaporation and large deformations can help understand the puffing process. ... En savoir plus

Modal Analysis of Functionally-Graded Metal-Ceramic Composite Plates

E. Gutierrez-Miravete[1], W. L. Saunders II[2], K. Pendley[3]
[1]Rensselaer at Hartford, Hartford, CT, USA
[2]General Dynamics Electric Boat, Groton, CT, USA
[3]United Technologies - Pratt & Whitney, East Hartford, CT, USA

The determination of the modes of vibration of Functionally Graded-Metal-Ceramic Composite plates is important in practice in order to prevent undesired resonances in structural components. This paper describes the application of COMSOL Multiphysics® software for the determination of the ... En savoir plus

Prediction of Noise Generated by Electromagnetic Forces in Induction Motors

M. K. Nguyen[1], R. Haettel[2], A. Daneryd[2]
[1]KTH, Stockholm, Sweden
[2]ABB Corporate Research,Västerås, Sweden

Induction motors, as any other industrial products, have to comply with various requirements on noise levels. Therefore, it is essential to use an appropriate prediction tool to verify and optimize the design of an induction motor with respect to the acoustic performances. The paper ... En savoir plus

Evaluation of Novel Wing Design for UAV

P. K. Bahumanyam[1]
[1]University of Alabama in Huntsville, Huntsville, AL, USA

Viable design alternative for the existing and fast growing UAVs which are optimized for unmanned flight is of great demand. Designing of a small scale UAV alternative to the AAI Aerosonde UAV has been considered changing the wing tail configuration of the vehicle analyzing both ... En savoir plus

Loading Conditions in the Feed Sparger of a Steam Drum Influenced by Thermal Shock

P. Goyal, A. Dutta, R.K. Singh, and K.K. Vaze
Bhabha Atomic Research Centre, Mumbai, Maharashtra, India

Steam drum in a nuclear power plant is one of the important components of Primary Heat Transport (PHT) system where steam is separated from the steam water mixture. Steam water mixture emanating from the reactor core is separated in a steam drum. Separated steam goes to the turbine ... En savoir plus

Premier

341–350 of 398

Dernier