Articles techniques et présentations

Recherche rapide

Ressources

Livres Blancs

Voyez comment la modélisation et la simulation sont utilisées par les industries La modélisation et la simulation multiphysiques pilotent l'innovation dans tous les grands secteurs d'activité et dans le monde universitaire — comme en témoignent les nombreuses utilisations présentées dans des articles et des posters techniques présentés par des ingénieurs, chercheurs et scientifiques à la Conférence COMSOL chaque année. Inspirez-vous des récents proceedings réunis ci-dessous, ou, pour trouver les présentations les plus intéressantes dans votre domaine d'intérêt, utilisez la recherche rapide.

Consultez les proceedings de la Conference COMSOL 2024

Terme recherché:

Comparison of Classic and Finned Piston Reciprocating Linear Air Compressor Using COMSOL Multiphyics®

M. Heidari[1], P. Barrade[1], A. Rufer[1]
[1]LEI, École Polytechnique Fédérale de Lausanne, Lausanne, Switzerland

The current work is dedicated to develop a FEM model for compressors using moving mesh. An analytical model is already developed for a classic compressor based on mass and energy balance and is extended to a finned piston compressor. COMSOL Multiphysics® is employed to verify the ... En savoir plus

Study of Supercritical Coal Fired Power Plant Dynamic Responses for Grid Code Compliance

A. Gil-Garcia[1], I. Kings[1], B. Al-Duri[1]
[1]University of Birmingham, School of Chemical Engineering, Edgbaston, Birmingham, UK

In clean coal technologies, improving energy conversion efficiency is one of the most important directions. Compared to traditional subcritical power plants, pressure-increased supercritical power plants improve the plant energy efficiency from 35% up to 45%. This work presents a study ... En savoir plus

Design of an Automated Thermal Cycler for Long-term Phase Change Material Phase Transition Stability Studies

D. Groulx[1], A. C. Kheirabadi[1]
[1]Mechanical Engineering, Dalhousie University, Halifax, NS, Canada

This paper highlights the use of the COMSOL Multiphysics® software during the design process of a thermal cycling system for regulated PCM phase transitioning. The primary purpose of the simulations was to predict the system behavior in response to an ON/OFF temperature control system ... En savoir plus

Numerical Simulation of the Lithium-Ion Battery Cell Discharge Characteristics

Z. Umar[1], D. Ledwoch[1], L. Komsiyska[1], S. Vasić[[1]
[1]EWE-Forschungszentrum für Energietechnologie e. V, Oldenburg, Germany

In general battery cells are charged/discharged using constant current or constant power expressed as C-Rates and P-Rates respectively. We are developing a single cell-level Li-Ion battery model in order to simulate the performance and the physicochemical phenomena under power ... En savoir plus

Battery Pack Temperature Distribution Simulation with COMSOL and MATLAB®

M. Masomtob[1], C. Schaeper[1], W. Zhou[1], D. Uwe Sauer[1]
[1]Electrochemical Energy Conversion and Storage Systems Group, Institute for Power Electronics and Electrical Drives (ISEA), RWTH Aachen University, Aachen, Germany

This work is to present an implementation of COMSOL with MATLAB® [1] for the liquid cooling system of a battery pack based on the physics in COMSOL. The m.file of a model of battery module from COMSOL 4.2 is exported and modified to run in MATLAB®, as well as is managed by using another ... En savoir plus

Model and App of Hydrophobic Meshes Used in Oil Spill Recovery

O. Silva [1], E. Coene [1], J. Molinero [1], B. Shafei [1]
[1] Amphos 21 Consulting S.L., Barcelona, Spain

Hydrophobic meshes are a new, promising technique for the recovery of spilled oil in the ocean. They allow to recover and store oil, while filtering it from the surrounding water. They are clean, efficient and can be used in continuously. These meshes have one drawback, however: if they ... En savoir plus

Modeling of HTPEM Fuel Cell Start-Up Process by Using COMSOL Multiphysics

Y. Wang[1], D. Uwe Sauer[1]
[1]Electrochemical Energy Conversion and Storage Systems, Institute for Power Electronics and Electrical Drives (ISEA), RWTH Aachen University, Aachen, Germany

HTPEM fuel cells are considered to be the next generation fuel cells. The electrochemical kinetics for electrode reactions are enhanced by using PBI membrane at an operation temperature between 160-180 °C comparing to LTPEM fuel cells. But starting HTPEM fuel cells from room temperature ... En savoir plus

Energy Pile Simulation – an Application of THM-Modeling

E. Holzbecher[1]
[1]Georg-August University, Göttingen, Germany

Energy piles, i.e. heat exchangers located within the foundation piles of buildings, are used for heating of cooling purposes. Although the absolute values of deformations and temperature gradients are low or moderate, the entire setting can be influenced by thermo-hydro-mechanical ... En savoir plus

3D Simulation of Heat and Moisture Diffusion in Constructions

M. Bianchi Janetti, and F. Ochs
University of Innsbruck
Unit Building Physics
Innsbruck, Austria

The simulation of heat and moisture transfer represents an essential resource in designing energy efficient buildings. In this paper a time-dependent wall model, consisting of several homogeneous domains, with third-type boundary conditions imposed on the surfaces, is implemented in the ... En savoir plus

Numerical Simulation of a Building Envelope with High Performance Materials

M.H. Baghban[1], P. Jostein Hovde[1], and A. Gustavsen[2]
[1]Civil and Transport Engineering Department, Norwegian University of Science and Technology, Trondheim, Norway
[2]Department of Architectural Design, History and Technology, Norwegian University of Science and Technology, Trondheim, Norway

Simulation tools for building physics problems play an important role in design and understanding the behavior of energy efficient buildings. There are different tools available for simulation of these problems, but each simulation tool has its own advantages and limitations. In this ... En savoir plus

Premier

341–350 of 505

Dernier