Articles techniques et présentations

Recherche rapide

Ressources

Livres Blancs

Voyez comment la modélisation et la simulation sont utilisées par les industries La modélisation et la simulation multiphysiques pilotent l'innovation dans tous les grands secteurs d'activité et dans le monde universitaire — comme en témoignent les nombreuses utilisations présentées dans des articles et des posters techniques présentés par des ingénieurs, chercheurs et scientifiques à la Conférence COMSOL chaque année. Inspirez-vous des récents proceedings réunis ci-dessous, ou, pour trouver les présentations les plus intéressantes dans votre domaine d'intérêt, utilisez la recherche rapide.

Consultez les proceedings de la Conference COMSOL 2024

Terme recherché:

Fluidmechanical Damping Analysis of Resonant Micromirrors with Out-of-plane Comb Drive

T. Klose[1], H. Conrad[2], T. Sandner[1], and H. Schenk[1]

[1]Fraunhofer Institute Photonic Microsystems (FhG-IPMS), Germany
[2]TU Dresden, Semiconductor and Microsystems Technology Laboratory, Germany

Damping is the liminting factor for the reachable maximum deflection. Thus, it is a very important issue for resonant microsystems. In this paper, we present a damping model for out-of-plane comb driven resonant micromirrors. The basic concept of this model is to attribute viscous ... En savoir plus

Design and Simulation of PDMS-Based Dry Electrode with Impurities

Roopa J. [1], B. S. Satyanarayana [1], K. S. Geetha [1], Yashus [1],
[1] R. V. College of Engineering, Bengaluru, Karnataka, India

COMSOL Multiphysics software was used to simulate the working of the electrode. The piezoelectric device physics was used to evaluate the displacement created and the potential generated due to piezoelectricity of PDMS. The potential created due to the flow of bio-signals between neurons ... En savoir plus

Finite Element Simulation of Love Wave based SAW Delay Line Using COMSOL Multiphysics

S. Trivedi [1], H. B. Nemade [2],
[1] Center for Nanotechnology, Indian Institute of Technology Guwahati, Guwahati, Assam, India
[2] Department of Electronics and Electrical Engineering, Indian Institute of Technology Guwahati, Guwahati, Assam, India

The paper presents 3D finite element simulation of Love wave based SAW delay line using COMSOL Multiphysics software. The device consists of a 36° YX Lithium Tantalate substrate covered with 4.7 μm thick SiO2 waveguide layer operating at λ = 12 μm. Time response study is used to ... En savoir plus

Optimization of MEMS Based Capacitive Accelerometer for Fully Implantable Hearing Aid Application

A. Dwivedi [1], G. Khanna [1],
[1] NIT Hamirpur, Hamirpur, Himachal Pradesh, India

This work describes the design and optimization of three prototypes of microelectromechanical systems (MEMS) capacitive accelerometer-based middle ear microphone. The microphone is intended for middle ear hearing aids as well as future fully implantable cochlear prosthesis. The analysis ... En savoir plus

Highly Sensitive Grating-Coupled Bloch Surface Wave Resonance Biosensor via Azimuthal Interrogation

V. Koju [1], W. M. Robertson [1],
[1] Middle Tennessee State University, Murfreesboro, TN, USA

A dielectric multilayer structure, with a grating profile on the surface layer, can couple light into a strongly confined surface wave, known as a Bloch surface wave. These surface modes can be used to design bio-sensors. The corrugated surface structure also enables azimuthal angular ... En savoir plus

Validation of the Acoustic Finite Element Model of a Very Light Jet Cavity Mock-up

F. Teuma Tsafack, K. Kochan, T. Kletschkowski, and D. Sachau
Helmut Schmidt University/ University of the Federal Armed Forces Hamburg, Germany

This paper presents an important step in developing a combined active noise- and audio system for a light jet. To prepare its installation both a wooden mock-up and a finite element model of the investigated cavity were created. Sensitivity analysis and key parameters selection were done ... En savoir plus

Simulation of the Acoustic Environment for the Manufacture of Graded Porosity Materials by Sonication

C. Torres-Sanchez, and J. R. Corney
University of Strathclyde, United Kingdom

Many materials require functionally graded cellular microstructures whose porosity is engineered to meet specific requirements of diverse applications. It has been shown in previous work that the bubble growth rate of a polymeric foam can be influenced by the surrounding acoustic ... En savoir plus

Simulation of a Dual Axis MEMS Seismometer For Building Monitoring System

M. A. Shah [1], F. Iqbal [1], B. L. Lee [1],
[1] Korea University of Technology and Education, Cheonan, Chungcheong, South Korea

A dual axis MEMS seismometer targeted for building monitoring system has been simulated for a full scale of ±5g acceleration. The design uses the capacitive effect for vibration sensing. This comb drive capacitive MEMS seismometer consists of 8 springs with two proof masses. The device ... En savoir plus

Ion Concentration and Electromechanical Actuation Simulations of Ionic Polymer-Metal Composites

K. J. Kim [1], T. Stalbaum [1], Q. Shen [1],
[1] Department of Mechanical Engineering, University of Nevada, Las Vegas, NV, USA

Ionic polymer-metal composite (IPMC) materials are promising candidates for soft robotics and artificial muscle applications. The primary actuation mechanism in such devices is ion migration in a polymer membrane, localized swelling, and a corresponding overall material deformation, ... En savoir plus

Models for Simulation Based Selection of 3D Multilayered Graphene Biosensors

E. Lacatus [1], G. C. Alecu [1], A. Tudor [1],
[1] Politehnica University of Bucharest, București, Romania

At the forefront of a new generation of sensors graphene and graphene composite materials are intensively studied for medical and biosensing applications. The outstanding electrical, mechanical and quantum properties of graphene make them a promising material solution to overlap the ... En savoir plus

Premier

411–420 of 694

Dernier