Articles techniques et présentations

Recherche rapide

Ressources

Livres Blancs

Voyez comment la modélisation et la simulation sont utilisées par les industries La modélisation et la simulation multiphysiques pilotent l'innovation dans tous les grands secteurs d'activité et dans le monde universitaire — comme en témoignent les nombreuses utilisations présentées dans des articles et des posters techniques présentés par des ingénieurs, chercheurs et scientifiques à la Conférence COMSOL chaque année. Inspirez-vous des récents proceedings réunis ci-dessous, ou, pour trouver les présentations les plus intéressantes dans votre domaine d'intérêt, utilisez la recherche rapide.

Consultez les proceedings de la Conference COMSOL 2024

Terme recherché:

Highly Concentrated Solar Radiation Measurement by Means of an Inverse Method

L. Mongibello[1], N. Bianco[2], R. Fucci[1], F. Moscariello[2]
[1]ENEA - Italian National Agency for New Technologies, Energy and Sustainable Economic Development, Portici, Italy
[2]DETEC - Università degli Studi di Napoli Federico II, Napoli, Italy

This work focuses on the numerical analysis conducted on the prototype sensor for the measurement of highly concentrated radiative heat fluxes, based on an inverse heat transfer method, realized at the ENEA Portici Research Center in collaboration with the DETEC department of the ... En savoir plus

Evaporative Cooling in Solar Absorption Chiller

J. Ma [1], M. J. Suh [1],
[1] Sam Houston State University, Huntsville, TX, USA

Solar cooling systems based on evaporation and absorption processes have been actively studied and different mechanisms based on various refrigerants are designed and developed. Amongst these systems, a single-stage close cycle design utilizing lithium bromide salt and water (LiBr-H2O) ... En savoir plus

Patch Antenna Model for Unmanned Aerial Vehicle

T. Eppes, I. Milanovic, and S. Thiruvengadam
University of Hartford
West Hartford, CT

Patch antennas are widely used in communications links with unmanned aerial vehicles. Their hemispherical send and receive patterns enable the systems to maintain radio frequency contact over a wide range of vehicular attitudes. A microstrip-fed design offers other attractive features ... En savoir plus

Carbon Steel Pipeline Wall Thickness Measurement Using Pulsed Eddy Current Technique

S. Roy[1], S. K. Pradhan[1], T. V. Shyam[2], B. S. V. G. Sharma[2],
[1] Atomic Energy Regulatory Board, Mumbai, Maharashtra, India
[2] Bhabha Atomic Research Centre, Mumbai, Maharashtra, India

Carbon Steel pipes are used as feeder pipes in Pressurized Heavy Water Nuclear Reactors for carrying the coolant from the inlet headers to the coolant channel and again from outlet of the coolant channel to the outlet headers and are part of the Primary Heat Transport (PHT) System of ... En savoir plus

Simulation Study of Electron Beam Profile Near the Aperture of Hollow Cathode for High Current Density Electron Beam Generation using COMSOL Multiphysics®

N. Gurjar[1], S. Kumari[1], K. Singhal[1], S. Jain[1], N. Kumar[1]
[1]CSIR-CEERI, India

High power Terahertz (THz) sources have become a topic of great interest for a wide variety of applications from medical science to security systems and from material science to telecommunication. The high output power of these THz sources mainly depends upon high current density and ... En savoir plus

Ventilation System of a Microwave Assisted Drying Kiln

A.-G. Ghiaus[1], M.-A. Istrate[1], A. Georgescu[1]
[1]Technical University of Civil Engineering, Bucharest, Romania

The paper presents the analysis and optimization of the ventilation system inside of a drying lumber kiln. As with any part of the manufacturing process, improper drying techniques cause quality degradation and considerable amount of energy loose. The improvement and optimization of ... En savoir plus

Numerical Solutions for the Lévêque Problem of Boundary Layer Mass or Heat Flux

E. Holzbecher
Weierstrass Institute for Applied Analysis and Stochastics (WIAS), Berlin, Germany

The Lévêque problem is an idealized simple situation concerning the influence of the boundary on the distribution of temperature or mass in Hagen-Poiseuille flow. Here, the performance of numerical solutions is examined for a range of Péclet numbers, spanning 11 orders of magnitude. We ... En savoir plus

Full Coupling of Flow, Thermal and Mechanical Effects in COMSOL Multiphysics® for Simulation of Enhanced Geothermal Reservoirs

D. Sijacic[1], P. Fokker[1]
[1]TNO, Utrecht, The Netherlands

The effective modeling of enhanced geothermal systems (EGS) requires the coupling of geomechanics, fluid flow and thermal processes. An understanding of the complete system with these coupled processes is vital, not just for reservoir stimulation targeted at enhancing reservoir ... En savoir plus

Comparative Numerical Studies of Scramjet Inlet Performance Using k-? Turbulence Model with Adaptive Grids

V. Gopal[1], R. Kolluru[1]
[1]BMS College of Engineering, Bangalore, Karnataka, India

Scramjet inlet design remains as a key aspect for hypersonic flight. To assess the inlet design, the performance parameters namely; air-capture ratio, total pressure efficiency, inlet drag coefficient, and kinetic energy efficiency are evaluated and analysed. In the current study ... En savoir plus

Metal Foam Tube Flow Characterisation

T. Spillmann[1]
[1]CSIRO, Energy Technology, Newcastle, New South Wales, Australia

In this study the flow through a tube filled with highly porous aluminium foam of three different pore sizes is analysed using COMSOL Multiphysics® CFD Module and compared to experimentally determined pressure drop data. Analyzing the flow through an array of pores allow the deduction of ... En savoir plus

Premier

721–730 of 1390

Dernier