Articles techniques et présentations

Recherche rapide

Ressources

Livres Blancs

Voyez comment la modélisation et la simulation sont utilisées par les industries La modélisation et la simulation multiphysiques pilotent l'innovation dans tous les grands secteurs d'activité et dans le monde universitaire — comme en témoignent les nombreuses utilisations présentées dans des articles et des posters techniques présentés par des ingénieurs, chercheurs et scientifiques à la Conférence COMSOL chaque année. Inspirez-vous des récents proceedings réunis ci-dessous, ou, pour trouver les présentations les plus intéressantes dans votre domaine d'intérêt, utilisez la recherche rapide.

Consultez les proceedings de la Conference COMSOL 2024

Terme recherché:

Improving Natural Convection in Redox Flow Batteries

Md Aslam Ansari [1], Dr. Sanjeev Kumar [1],
[1] Indian Institute of Science, Bangalore, Karnataka, India

Harvesting of renewable energy requires efficient energy storage systems. Rechargeable flow batteries offer certain advantages over other energy storage techniques in use, such as the lifting of water, compression of air, flywheel, etc. In a flow battery, electrolyte flowing through ... En savoir plus

Conjugate Heat Transfer Simulation of Argon Gas Heater for ARPS in Pyroprocessing Facility

Sourabh Agarwal [1], K. Revathy [1], A.S Vipin [1], S.P Ruhela [1], B. Muralidharan [1], B.P Reddy [1],
[1] Indira Gandhi Centre for Atomic Research, Kalpakkam, Tamil Nadu, India

PyroProcessing Research and Development Facility (PPRDF) is being setup in IGCAR to develop pyroprocessing technology. It consists of a large argon cell attached with Argon Recirculation and Purification System (ARPS). Once through Argon gas heater is an important process equipment in ... En savoir plus

Evaporative Cooling in Solar Absorption Chiller

J. Ma [1], M. J. Suh [1],
[1] Sam Houston State University, Huntsville, TX, USA

Solar cooling systems based on evaporation and absorption processes have been actively studied and different mechanisms based on various refrigerants are designed and developed. Amongst these systems, a single-stage close cycle design utilizing lithium bromide salt and water (LiBr-H2O) ... En savoir plus

Numerical Solutions for the Lévêque Problem of Boundary Layer Mass or Heat Flux

E. Holzbecher
Weierstrass Institute for Applied Analysis and Stochastics (WIAS), Berlin, Germany

The Lévêque problem is an idealized simple situation concerning the influence of the boundary on the distribution of temperature or mass in Hagen-Poiseuille flow. Here, the performance of numerical solutions is examined for a range of Péclet numbers, spanning 11 orders of magnitude. We ... En savoir plus

Study of an Electroacoustic Absorber

A-S. Moreau[1], H. Lissek[1], and R. Boulandet[1]
[1]EPFL-STI-IEL-LEMA, Ecole Polytechnique Fédérale de Lausanne, Lausanne, Switzerland

In this paper, the underlying concept of electroacoustic absorbers is studied with the help of Comsol Multiphysics® Acoustics Module. Among the different ways to obtain variable acoustic properties on an electroacoustic transducer's voicing face, there is the shunting of the ... En savoir plus

Modeling Polybenzimidazole/Phosphoric Acid Membrane Behaviour in a HTPEM Fuel Cell

C. Siegel[1,2], G. Bandlamudi[1,2], and A. Heinzel[1,2]
[1]Zentrum für BrennstoffzellenTechnik (ZBT) gGmbH, Duisburg, Germany
[2]Institut für Energie- und Umweltverfahrenstechnik, University of Duisburg-Essen, Duisburg, Germany

Phosphoric acid doped polybenzimidazole (PBI) membranes are commonly used in today’s high-temperature polymer-electrolyte-membrane (HTPEM) fuel cell technology. COMSOL Multiphysics is used to model and simulate the three-dimensional, single-phase, non-isothermal overall cell behaviour ... En savoir plus

Shape, Convection and Convergence

R. Pryor
Pryor Knowledge Systems, Inc., Bloomfield Hills, MI, USA

COMSOL Multiphysics software, when properly configured, can readily solve modeling problems in the laminar flow regime using the standard Navier-Stokes equations or in the fully turbulent flow regime using the kappa-epsilon model. Failure to solve a particular model is typically ... En savoir plus

Accuracy Assessment of The Linear Induction Motor Performance using Adaptive FEM

M. Manna[1], S. Marwaha[1], and C. Vasudeva[1]
[1] Department of Electrical & Instrumentation Engineering, Sant Longowal Institute of Engineering and Technology , Longowal (Deemed University), Punjab, India

The majority of electrical machines are designed to produce the rotary motion, there by exploiting the blessing of circularity which man has enjoyed since the discovery of the wheel. Electromagnetic forces may also be employed to produce the linear motion resulting in linear motion ... En savoir plus

Modeling Contact Line Dynamics in Evaporating Menisci

J. Plawsky[1], A. Chatterjee[1], and P.C. Wayner Jr.[1]
[1]Department of Chemical and Biological Engineering, Rensselaer Polytechnic Institute, Troy, New York, USA

The Constrained Vapor Bubble is a fundamental fluid mechanics experiment that is scheduled to run aboard the International Space Station starting in August 2009. The experiment is focused on looking at evaporation and condensation processes at the contact line, where vapor, liquid and ... En savoir plus

Modeling of Nonlinear and Non-stationary Multi-vortex Behavior of Electronic Crystal in Restricted Gemoetries of Nano Junctions

T. Yi, Y. Luo, and S. Brazovskii
CNRS
LPTMS URM8626
Université Paris-sud
Orsay, France

Electronic Crystals are common forms of organization of charge in solids. They appear widely from nano-structure semiconductors to synthetic organic conductors. Charge density wave, the best treated kind of electronic crystal, can readjust its elementary units by creation of topological ... En savoir plus

Premier

741–750 of 1391

Dernier