Articles techniques et présentations

Recherche rapide

Ressources

Livres Blancs

Voyez comment la modélisation et la simulation sont utilisées par les industries La modélisation et la simulation multiphysiques pilotent l'innovation dans tous les grands secteurs d'activité et dans le monde universitaire — comme en témoignent les nombreuses utilisations présentées dans des articles et des posters techniques présentés par des ingénieurs, chercheurs et scientifiques à la Conférence COMSOL chaque année. Inspirez-vous des récents proceedings réunis ci-dessous, ou, pour trouver les présentations les plus intéressantes dans votre domaine d'intérêt, utilisez la recherche rapide.

Consultez les proceedings de la Conference COMSOL 2024

Toutes

Boston 2025

Terme recherché:

transducer

The Simulation of Motion of a Slider upon a Stator Due to Frictional Force Using COMSOL Multiphysics® Software

H. B. Nemade[1]
[1]Indian Institute of Technology Guwahati, Guwahati, Assam, India

The Surface Acoustic Wave (SAW) linear motor was studied which is developed utilizing the friction principle for driving. The principle says that, when a slider is placed on the Rayleigh waves generated on a stator, the slider moves in reverse direction of the wave due to friction ... En savoir plus

MEMS Based Silicon Load Cell for Weighing Applications

D. Chauhan[1], B. D. Pant[2]
[1]Kurukshetra University, Kurukshetra, Haryana, India
[2]CSIR- Central Electronics Engineering Research Institute, Pilani, Rajasthan, India

Load cells are force sensors, which are used in weighing equipment. The objective of this work is to develop MEMS based load cell. In this work two different load cell designs were simulated. First design is based on compressing a meander like polysilicon strain gage for the measurement ... En savoir plus

Simulation and Experimental Characterizations of a Thin Touch Mode Capacitive Pressure Sensor

A.-M. El Guamra [1], D. Bühlmann [1], F. Moreillon [1], L. Vansteenkiste [1], P. Büchler [2], A. Stahel [3], P. Passeraub [1],
[1] HES-SO University of Applied Sciences Western Switzerland, Delémont, Switzerland
[2] Institute for Surgical Technology & Biomechanics, University of Bern, Bern, Switzerland
[3] Bern University of Applied Sciences Engineering and Information Technology, Bern, Switzerland

Introduction: This study describes a thin and low-cost capacitive pressure sensor in touch mode (TM) for monitoring fluid pressure from 0 to 40kPa in fluidic chambers with Luer fittings for medical applications. TM provides good linearity, large measuring range and large overload ... En savoir plus

Two-Dimensional FEM Simulation of Ultrasonic Wave Propagation in Isotropic Solid Media using COMSOL

B. Ghose[1], K. Balasubramaniam[2], C.V. Krishnamurthy[3], and A.S. Rao[1]
[1] High Energy Materials Research Laboratory, Pune, Maharashtra, India
[2] Center for Non Destructive Evaluation, Department of Mechanical Engineering, IIT Madras Chennai, Tamil Nadu, India
[3] Department of Physics, IIT Madras,Chennai, Tamil Nadu, India

Ultrasonic Testing (UT) is one of the important Non-Destructive Evaluation (NDE) technique widely used for characterisation of materials as well as detection and characterisation of flaws present in the material used in various industries. There are many different important materials ... En savoir plus

COMSOL Multiphysics® Software for Modeling STW Devices

V. Plessky [1], V. Yantchev [2]
[1] GVR Trade SA, Gorgier, Swizterland
[2] Individual Consultant, Sofia, Bulgaria

Electroacoustic resonators employing surface acoustic waves (SAW) are commercially widely used in RF filters, low noise frequency sources as well as various sensors. In all of these applications the resonance quality factor appears to be a limiting performance factor. Quite often ... En savoir plus

AlN/ZnO/Silicon Structure Combining Surface Acoustic Waves And Waveguiding Layer Acoustic Wave

O. Legrani[1], O. Elmazria[1], S. Zhgoon [2], L. Le Brizoual[3], and A. Bartasyte[1]
[1]Institut Jean Lamour, CNRS-Nancy University, Vandoeuvre lès Nancy, France
[2]Moscow Power Engineering Institute, Krasnokazarmennaja, Moscow, Russia
[3]Institut des Matériaux Jean Rouxel, Université Nantes, CNRS, Nantes, France

In this work, the theoretical study for the realization of waveguiding layer acoustic waves devices based on AlN/IDT/ZnO/Silicon structure using the modeling software COMSOL Multiphysics (2D) is presented. The effect of thicknesses of AlN and ZnO thin films on the evolution of frequency ... En savoir plus

Comsol’s New Thermoviscous Interface and Computationally Efficient Alternative Formulations for FEM

W. R. Kampinga[1], and Y. H. Wijnant[2]
[1]Reden, Hengelo, Netherlands
[2]University of Twente, Enschede, Netherlands

Three efficient alternatives to the model in COMSOL’s thermoacoustics interface are presented. The higher efficiency of these models are explained from theory and are demonstrated by means of two examples. En savoir plus

Simulation of an Ultrasonic Immersion Test for the Characterization of Anisotropic Materials

A. Castellano[1], P. Foti[1], A. Fraddosio[1], S. Marzano[1], M.D. Piccioni[1], D. Scardigno[1]
[1]DICAR, Politecnico di Bari, Bari, Italy

Introduction: Improving the capability of nondestructive evaluations requires the analysis of suitable models dealing with the physical and mechanical phenomena involved in the experiments. For example, ultrasonic tests may be a powerful, fast and effective method for nondestructive ... En savoir plus

CFD Analysis of Loss Of Vacuum Accident for Safety Application in Experimental Fusion Reactor Facility

C. Bellecci[1], P. Gaudio[1], I. Lupelli[1], A. Malizia[1], M.T. Porfiri[2], R. Quaranta[1], and M. Richetta[1]

[1]EURATOM, Faculty of Engineering, University of Rome “Tor Vergata”, Roma, Italy
[2]ENEA Nuclear Fusion Tecnologies, Frascati, Roma, Italy

In an experimental nuclear fusion facility dust is generated both during normal machine operations and by macroscopic erosion of the plasma facing materials due to intense thermal loads. This dust can be mobilized by air ingress in case of LOVA (Loss of Vacuum Accident) threaten safety ... En savoir plus

Improvements in the Modeling of the Self-ignition of Tetrafluoroethylene

M. Beckmann-Kluge, F. Ferrero, V. Schröder, A. Acikalin, and J. Steinbach
Federal Institute for Materials Research and Testing, Technical University, Berlin, Germany

Tetrafluoroethylene (TFE) is a gas widely employed in industry, which can under specific circumstances experience an exothermic dimerization to octafluorocyclobutane. If the heat generated by this reaction cannot be dissipated to the surroundings, the temperature inside the reactor will ... En savoir plus

Premier

211–220 of 248

Dernier