Articles techniques et présentations

Recherche rapide

Ressources

Livres Blancs

Voyez comment la modélisation et la simulation sont utilisées par les industries La modélisation et la simulation multiphysiques pilotent l'innovation dans tous les grands secteurs d'activité et dans le monde universitaire — comme en témoignent les nombreuses utilisations présentées dans des articles et des posters techniques présentés par des ingénieurs, chercheurs et scientifiques à la Conférence COMSOL chaque année. Inspirez-vous des récents proceedings réunis ci-dessous, ou, pour trouver les présentations les plus intéressantes dans votre domaine d'intérêt, utilisez la recherche rapide.

Consultez les proceedings de la Conference COMSOL 2024

Terme recherché:

Modeling Conventional Swing of a Cricket Ball

R. Latchman [1], A. Pooransingh [1],
[1] University of the West Indies - St. Augustine, St. Augustine, Trinidad and Tobago

Conventional swing is one phenomenon which a bowler uses to gain an advantage over the batsman. This study involved simulating conventional swing in the CFD Module of COMSOL Multiphysics® software and comparing the simulated results with experimental results of previous researchers. The ... En savoir plus

The Effects of the Contact Angle on the Dynamics of Water Droplet Impingement

J. Hu [1], X. Huang [2], X. Xiong [1], K. T. Wan [2],
[1] University of Bridgeport, Bridgeport, CT, USA
[2] Northeastern University, Boston, MA, USA

INTRODUCTION The dynamic behavior of droplet impingement on a solid surface is important to many engineering applications, such as rain drops on automobile windshields, inkjet deposition and metal deposition in manufacturing processes, spray cooling of electronics, and spray coating for ... En savoir plus

Measurement of Blood Flowrate in Large Blood Vessels Using Magnetic Flowmeter

S. Dasgupta [1], K. Ravikumar [1], P. Nenninger [2], F. Gotthardt [2],
[1] ABB, Bangalore, Karnataka, India.
[2] ABB, Gottingen, Germany.

This paper is an investigation into the effect of blood vessel movement on measurement accuracy of blood flow rate using magnetic flow meters. The investigation used a Finite Element model of the magnetic flowmeter built using COMSOL Multiphysics® software by integrating the modules of ... En savoir plus

Numerical Simulations and Experimental Verification of Laser Welding of Nylon 6

Santosh Kumar Gupta [1], Sanjib Jaypuria [1], Dilip Kumar Pratihar [1], Partha Saha [1],
[1] Indian Institute of Technology Kharagpur, Kharagpur, West Bengal, India

Laser welding is often considered to be a superior technique over different conventional welding methods and has been gradually evolved as an efficient manufacturing process. It is a high energy density fabrication process and generally employed for fabricating intricate shapes/contours ... En savoir plus

A Study on Hydrodynamics of Melt Expulsion in Pulsed Nd: YAG Laser Drilling of Titanium

S. Sharma [1], Y. Pachuary [2], S. N. Akhtar [3], J. Ramkumar [1],
[1] Indian Institute of Technology Kanpur, Kanpur, India
[2] Indian Institute of Information Technology, Design and Manufacturing, Jabalpur, India
[3] Integral University, Lucknow, India

Laser drilling of titanium and its alloys is widely used in aerospace industry, as it offers selective removal of material at high accuracy and speed. However, laser drilling often inherits defects such as large heat affected zone, micro cracks and recast layer. These defects depend upon ... En savoir plus

Finite Element Simulation of Shear Wave Propagation Induced by a VCTE Probe

S. Audière[1,2], M. Charbit[1], E. Angelini[2], V. Miette[2], J. Oudry[2], and L. Sandrin[2]
[1]Institut Telecom, Telecom ParisTech, Paris, France
[2]Echosens, Paris, France

The Fibroscan® (Echosens, Paris, France) device based on vibration–controlled transient elastography (VCTE) is used to non– invasively assess liver stiffness correlated to the hepatic fibrosis. Stiffness is quantified by measuring the velocity of a low–frequency shear wave traveling ... En savoir plus

Benchmark Model: Natural Convection of Water-Aluminum Oxide Nanofluids in a Square Cavity

M. Z. Saghir [1], A. Ahadi [1], A. A. Mohamad [2],
[1] Department of Mechanical Engineering, Ryerson University, Toronto, ON, Canada
[2] Department of Mechanical Engineering, University of Calgary, Calgary, AB, Canada

Nanofluids is a new class of fluid consisting of particles in a liquid. Different base liquid has been proposed and the most common one is water. The concentration of these particles can range from 0.1% to 5% or greater. Different numerical models have been proposed to solve this ... En savoir plus

Simulating Wear in Disc Brakes

N. H. Elabbasi[1], M. J. Hancock[1], S. B. Brown[1]
[1]Veryst Engineering, LLC, Needham, MA, USA

Wear is a complex phenomenon relevant to many problems involving frictional contact, such as mechanical brakes, seals, metal forming, and orthopedic implants. The rate of wear depends on the properties of the contacting materials and operating conditions. One widely used model of wear is ... En savoir plus

Simulating Wear in Disc Brakes

N. H. Elabbasi[1], M. J. Hancock[1], S. B. Brown[1]
[1]Veryst Engineering, LLC., Needham, MA, USA

Exergy Analysis of Polymer Flooding in Clastic Reservoirs

A. Hassan [1], H. Bruining [2], T. Musa [3], R. Farajzadeh [2],
[1] Delft University of Technology, Delft, The Netherlands, and Sudan University of Science and Technology, Khartoum, Sudan
[2] Delft University of Technology, Delft, The Netherlands
[3] Sudan University of Science and Technology, Khartoum, Sudan

Using a 1-D model of polymer displacement, we analyze the exergy (maximum attainable work) balance of viscosified water, e.g. with Arabic gum. The 1-D model shows the principle how such an analysis can be done. A comparison as to the displacement efficiency is made between three ... En savoir plus

Premier

421–430 of 1391

Dernier